Wanted to mess around with geometry and see if i could make a better baffle then the round ones normaly made. We need to think outside the box with 3D printing, We are no longer stuck making round baffles.
Tested Print Settings
PLA+ or Better .12mm Layers 5 Walls 100% Infill Print with up, front port on hotplate No Supports
Threaded in 1/2-28, Tested with 22lr Sub-Sonics and Standard.
Be sure to inspect the suppressor to make sure there is no deformation or melted areas.
ver. b3 (NOW INCLUDES ORIGNAL SOLIDWORKS FILES)
This is a Auto Sear for Glocks, It does not have a selector.
This is untested.
This is a felony to own or make in the USA.
Based off a metal version thats going around that they are selling.
Plastic *MIGHT* work but it would be best to CNC, or Cast in metal.
Included is a .3mf file and the Original SolidWorks file for editiing if needed.
Don't sell this shit.
This is a prototype suppressor design for the Henry H001 22lr gun. The goal of this project is to make a good performing suppressor that can attach to a H001 without any modification AND still allow you to use the original magazine tube without removing it.
In this package are the CAD files and 3mf. There are two versions of the suppressor using different baffle designs. There is also a blank mount to help you to dev your own baffle design.
To mount you will need 2 M3 20mm Screws and 2 M3 Nuts, you may also want to use a 12.50mm OD O-Ring to block gass from the interface area.
Check the ReadMe for printing and other info.
A 3D printed Suppressor for your Gambino or Cabfare 22lr gun!
Print Settings:
PLA+ or Stronger
.16 or Lower Detail
100% Infill
20 Walls Top and Bottom
Print front down on bed
NO Supports
Build:
Use a 65mm 22lr Rifled Barrel Liner with a OD of 8mm
Use a 8mm drill bit to pre-drill the hole in the barrel from the breech side down, keep stright!
Use pliers or sandpaper to scratch the outside of the barrel for more surface area
Use 2 part strong Epoxy (JB Weld, Locktight, etc) and wipe the barrels outside with a generus layer
Press the barrel into the barrel body from the breech side, make sure end of liner is level with the barrel frame!
Clean leftover Epoxy, If some epoxy gets in the barrel liner clean out.
NOTICE:
Please now your laws before printing, This is a NFA item in the United States!
Be sure that your barrel liner is inline with the ports of the baffles or you will have baffle strikes!
Always do test shots remotely with a vice and string!
Use Sub-Sonic ammo like Aquila SSS for best results.
Auther: nameisnight
Details:
This is a printed copy of a rapid fire device sold on ebay, it attaches to the lever of the gun and when you cock the gun it presses the trigger.
Tested working on a Henry H001, Should work with other similer leveractions.
Printing:
Print with round side down on bed, use Brim to aid in printing.
Tested in PLA+ at 0.16 Layer hight and 12% Gyroid Infill
Installation:
Clip the device wit hthe round side facing the trigger area of the gun, the side with a ramp should be facing twords the barrel.
Push device so it just presses the trigger.
When actioning the gun the device should press the trigger as soone as the action closes.
Troubleshooting:
If the device moves you can use tape to help hold it in place, or try printing at a different resolution.
**10/17/2023 - Updated to include step and stl as requested. **
Simple and easy to print, a 3/4-10 threaded muzzle device to direct the sound forward away from the shooter. Made for the VMAC9 but would work with most firearms with the same threads, including my 22lr Muzzle.
Print Settings:
PLA+
.20 or Better
100% Infill
5 Walls
No Supports
Raft/Rim if needed.
Print with threads on bed.
For those who live in cucked states where you need a magazine lock. Print both parts use 2 part epoxy to set together. To remove use heat, fire or violence.
This is a custom-made Clipping jig for a Chinese solvent trap, Made by Caska with Love.
Please be sure your solvent trap is equal to these specs to make sure this jig will work for you.
Overall Length: 9"
Tube length: 8.25”
Outside Diameter: 1.6"
Internal Diameter: 1.38"
Weight: 29 oz
Example of Kit: https://kmwhisper.com/collections/solvent-traps/products/form-1-kit (This can be found direct from china for far less)
What you need:
2x 6x17x6 mm Bearings : https://www.amazon.com/uxcell-606-2RS-Bearing-6x17x6 mm-Bearings/dp/B07MX9V7VB/
1x 6.00 mm (15/64th) HSS Drill bit : https://www.amazon.com/DEWALT-DW1915-64-Inch-Ferrous-Oxide/dp/B00004YMEN/
1x Clamp or 2x M3x50 mm Screws and M3 Nuts
Printing:
Print in PLA or Better
100% Infill
If you need Supports, Supports where NOT touching the build plate
Print with Words on Build Plate
Instructions:
Press fit bearings into top (where the words are) and bottom slots. Use Glue if needed.
Insert K-Cup with the top (Not the cone) twords the top (words) of the jig and press it in.
Use a C-Clamp OR M3x50 mm Bolts and Nuts to tighten the jig around the K-Cup.
Use DrillPress to slowly drill hole.
Unclasp/Unbolt to release the K-Cup (might need to push out)
Notes:
Do not go fast as it can break bits and might make the jig warp/melt.
You will need to cut/break the printed back wall (notch where on the bolt holes side) so the bottom of the jig can squeeze around the cups.