LBRY Block Explorer

LBRY Claims • rosch-auftriebskraftwerk-aukw-kinetic

e15e69a3bda77301aa6b7a77308ff9e48103c453

Published By
Created On
7 Jan 2020 22:53:44 UTC
Transaction ID
Cost
Safe for Work
Free
Yes
Rosch Auftriebskraftwerk AuKW - Kinetic Power Plant KPP - Belgrad Chaincoupling to Generator
Rosch Auftriebskraftwerk AuKW - Kinetic Power Plant KPP - Belgrad Chaincoupling to Generator
http://www.overunity.de/1797/rosch-auftriebskraftwerk-gaia-auftriebs-kraftwerk-wie-es-funktioniert/msg38700/#msg38700

Deutsche Übersetzung unten.

Here in this video you see the chaincoupling of the Rosch buoyancy Kinetic Power Plant KPP in Belgrad, Serbia, which shows us that the Generator is only running in idle mode and does not produce all the claimed power of about 12 KWatts !
You can see, that the chain directly at the generator is hanging loose on both upper and lower side.
So this tell us, that the generator just runs at idle speed and no
electrical load is attached to it.
Also the first uppen chain at the green tank at the top is just too weak to pull at this torque, if a real 12 KWatt load would be hanging on the generator. It would just rip apart...
So the conclusion is, the power output at the ROSCH facility comes from the house-grid from the input control box where some cables go down to the floor and along the wall and then up again to the output power box. Also there the frequency is very constant and only varying from 50.00 to 50.01 Hz, which a mechanical generator could not do so precise.
Also no tester was allowed to measure directly at the generator output only !
So this setup seems to be a full fake to try to catch investors...
Beware !
Please compare to these pictures and the movie from Rosch:
http://www.rosch.ag/index.php/de/entwicklungen/aufriebskraftwerk/kpp-galerie
and
https://www.youtube.com/watch?v=jNbbNafIUbc

German Description:
Hier in dem neuen Video, dass ich von einem Freund zugeschickt bekommen habe, der bei Rosch in Belgrad war und sich dort das Auftriebskraftwerk angeschaut hat, kann man sehen, dass die Kette, die direkt an dem Generator hängt, sehr lose hängt, oben wie auch unten...also daraus kann man schliessen, dass der Generator im Leerlauf läuft und keine elektrische Last an dem Generator angeschlossen ist... Wenn er eine Last antreiben würde, dann würde der obere Teil der Kette straff gespannt sein, da er ja dann eine Gegenkraft überwinden müsste...ist hier aber nicht der Fall!
Nur die obere Kette direkt am Ausgang des Auftriebspaternosters ist auf der rechten Seite gespannt, so dass man sehen kann, dass der Auftriebspaternotor wirklich den Generator antreibt...allerdings
eben nur im Leerlauf... und die ganz obere Kette wäre auch gar nicht stark genug dort bei der geringen Drehzahl das Drehmoment von ca. 12 KWatt zu ziehen... sie würde schlichtweg zerreissen.
Ausserdem durften Besucher auch nur NACH der Ausgangsbox messen und nicht direkt am Generator ! Da die Frequenz an der Ausgangsbox auch nur von 50.00 zu 50.01 Hz schwankt, sieht man schon, dass so genau kein mechanischer Generator sein kann und der S
...
https://www.youtube.com/watch?v=Lee5Q56YbJ4
Author
Content Type
Unspecified
video/mp4
Language
Unspecified
Open in LBRY

More from the publisher

Controlling
VIDEO
NEW H
Controlling
VIDEO
FREE
Controlling
VIDEO
GRAVI
Controlling
VIDEO
CHEMT
Controlling
VIDEO
TEST
Controlling
VIDEO
HOMEM
Controlling
VIDEO
ELECT
Controlling
VIDEO
NEW M
Controlling
VIDEO
IGORS