I got this from an e-sales company. The cost was $150 with tax and shipping. I was viewing this, melting things, with some shaded safety glasses...I think the shade was maybe a #3, not 5, like I said in video. These generators are advertised for melting the edges of plexiglass for artistic work, making the edge clear from saw marks, etc. I was supposed to use a solution of 15% LYE. I would then have to use 150 grams of lye for 1 liter of distilled water. I only used 100 grams. I like the amps and resulting flame right there. So I will just run it like this, I believe. No sense pushing the power supply, I feel. This is way more efficient than the one I made. I was running 12 volts at 80 amps with a smaller flame. I love this thing. I am only hooking up the red gas hose on my torch, the green hose has nothing on it. And as a bonus I can use it to make hydrogen rich water for health...so that is a subject all it's own. This will weld or solder or braze aluminum, copper, stainless steel...etc, with a very clean flame. There is ZERO carbon in water, so no CO2 or CO or any soot from flame. The only by product of burning this fuel is water. Yes, fuel from water will save me a lot of money from having to buy any butane and propane, and acetylene from now on. This is "brown's gas"... hydrogen and oxygen both, are sent to torch head mixed together. Melts rocks too...so cool! Just another scrap of NON-dependence !!!
...
https://www.youtube.com/watch?v=WzRrYk6lfkc
I am making my own carport kit from scratch. I have some 10 foot long EMT pipe to bend. I used 1 1/4" EMT pipe and some 1 1/2" EMT pipe so they fit together. This method will save a massive amount of cutting and welding pipe sections to make corner pipe supports. I made one like that before, it was a lot of work. This pipe bender should make it easy. Once I decided on a pitch for the roof and the width of the whole thing, it was easy. I have to use 36 inch steel sheeting, so that had to be figured in the width also. I will have a roof area of about 11 feet by 20 feet when I am done. The legs will be angled out a bit for stability. I also need to put 26" more pipe length on the legs for a good height so I can walk under it without hitting my head. The bottom sheet of roof material should wrap down around the bends I just made a few inches. I got the EMT at home depot and the bender at harbor freight. The next video will show the roof and legs for it.
...
https://www.youtube.com/watch?v=Cjdlkd3Insk
This is the second part of the carport build. The sheeting cost was just $200 and another $100 approximately for the EMT. So this is 10 feet plus by 20 feet long. I had the spikes in my stash. How do you like the pocket hole cam at the end? My daughter bought the little hero camera for me, so I wanted to show it off. Have fun, any questions...please ask.
...
https://www.youtube.com/watch?v=ZSCW7sg1tq4
Some more information on the build of this project. Please watch and share the information and videos here. This will, and does, kill the bacteria in my well that causes a sulfur odor in my water. No need to have expensive equipment that can "fix" my water problems. This can save lives by providing a simple and inexpensive method of killing pathogens in drinking water supplies. Testing should be done to see what pathogens are affected by this method. Please share and send these videos all over the planet, to help our fellow "man". Greed and shelfishness should stop today, please help me, help others. No need to buy poisoness chemicals and put them in my well anymore to kill bacteria. A WORD OF CAUTION... there is a chance of a build up of hydrogen gas if not allowed to escape to the atmosphere.
...
https://www.youtube.com/watch?v=0UGVbvcqJbo
Something like a Bedini motor only sideways. One coil drives this motor with a pick up sensor to set timing of pulses. It charged a battery that supplied the power to run it. I had it charge .1 volt increase in 16 hours of run time once. Can't run a house on that. Old old video.
...
https://www.youtube.com/watch?v=IHhq1iTsj14
Just the start of vinyl siding project. I go into some tips of installing siding in the following video. Just some small look at the process involved here.
...
https://www.youtube.com/watch?v=B4QVF44Y3LE
Just using leftover 1X4 wood to make some window shutters. So simple to do and make repeatable. I made my length match the window height itself and not match the "J" channel dimension. The wood is inexpensive and easy to work with. I think it makes a big change in how the siding job looks. Now it looks finished. The spacer I used was 3/4" wide and I only used two vertical pieces, but I see a lot with three also. I had to use small blocks behind shutters to stand off the siding evenly because of the vertical rib or batten. The screws I used to attach to the house were 3.5". With the wood I used I would recommend pre drilling all screw holes so you don't split any wood by screwing too near any edges, or ends of the wood. Do you like the color? Should it have been white?
...
https://www.youtube.com/watch?v=WY0Axe0fkQA
Is your LED light fixture too bright? Just a quick coat of flat white spray paint. One side of the cover. This defuses the light. You might thank me for this fix. Soooo much nicer to work around this light now. Dim your LED light!
...
https://www.youtube.com/watch?v=d8WXPT4Vysk