Keychains with a silhouette that is dimensionally accurate to the real life calibers they represent.
Collection 1 for handguns come in six calibers: 10mm Auto, 40S&W, .357 Magnum, .38 Special, .45 ACP, and 9x19 NATO.
Now you can continue the constant caliber wars debate. Which is better: 9mm or .45? Is 40S&W really that much better than 9mm? Or are all the calibers peashooters compared to the hand cannon 10mm?
Put multiple on your keys, show the boys what caliber you trust your life with :D
"Revolt" Push Dagger V1.0.1: Laffs Dynamics
A 3DP compact push dagger with a widened spear point to resist tip breakage. The tip is thicker than the previous
Laffs Dynamics released push dagger. Features a wide blade, with a ridged grip.
Update V1.0.1: Changed recommended print settings for better device strength, updated name of designer.
Printer Used: Ender 3 V2
Filament Used: PLA+
Print Settings:
Extruder: 220C
Bed: 56C
First Layer Print Height: .18mm
Standard Layer Height: .12mm
Wall Thickness: .40
Wall Perimeters: 7+
Infill: 50%
Evo Picatinny AFG V1.2.1: Laffs Dynamics
An angled foregrip designed specifically to match up to the OEM CZ Scorpion Evo III Pistol/SMG handguard.
Utilizes the entire bottom picatinny rail on the handguard. Has front and rear hand stops, also has ridges
that wrap around the AFG.
(Can be used on other weapon picatinny handguards)
Update V1.2.1: Tightened picatinny rail slot tolerances. Thickened handstops ends by 2mm. Relabeled designer's brand.
Printer Used: Monoprice Maker Select Plus
Filament Used: PLA+
Print Settings:
Extruder: 218C
Bed: 54C
First Layer Print Height: .18mm
Standard Layer Height: .14mm
Wall Thickness: .40
Wall Perimeters: 4 - 5
Infill: 25%
Infill Pattern: Gyroid
Material Flow: 100%
Support Material Percentage: 20%
Hardware Required:
1x M4x30mm Bolt (Can be ground down to 28mm so it doesn't stick out the side)
1x M4 Hex Nut
Trigger Cut Beretta 21A Bobcat Grip Panels: Laffs Dynamics
A grip panel set for Bobkatz 3DP pistol and the Beretta 21 A Bobcat pistol, with a scallop across the front section of the
panels.
Printer Used: Ender 3 V2
Filament Used: PLA+
Print Settings:
Extruder: 218C
Bed: 56C
First Layer Print Height: .20mm
Standard Layer Height: .12mm
Wall Thickness: .40
Wall Perimeters: 5+
Infill: 20%+
Support Material Percentage: 18%
Accreditations:
Gerald.Katz: Creator of the Bobkatz 3DP Pistol Frame; used the base grip model from their design release.
RDR T1 V1.0.1: FFFTech/FFFTechnology
A set of basic risers for red dot optics that use the common Aimpoint T1 mounting footprint. The +15mm
to +25mm risers have a hollow section through their bodies to allow for use of iron sights.
Six risers are available: (READ NOTES)
* Standard Mount
* +5mm
* +10mm
* +15mm
* +20mm
* +25mm
Update V1.0.2: The number of parts under "hardware" was previously incorrect; stating only needing one of each part.
The correct amount is two of each part.
Printer Used: Ender 3 V2
Filament Used: PLA+
Print Settings:
Extruder: 220C
Bed: 56C
First Layer Print Height: .20mm
Standard Layer Height: .12mm
Wall Thickness: .40mm
Wall Perimeters: 6+
Infill: 25%+
Infill Pattern: Gyroid
Material Flow: 100%
Support Material Percentage: 18%
Print the mount/riser upside-down
Hardware Needed:
1x M5x30 Hex Socketed Machine Screw/Bolt
1x M5 Hex Nut (Be sure both bolt & nut are the same thread pitch.)
Notes:
1) The height of the Standard mount is (from the top of the picatinny rail to the bottom of the red dot's mounting surface) is
5.53mm. That means if you attach the +20mm riser, it's actual height is 25.53mm. The millimeter designations for the risers are
based on the addition to the Standard mount's height, not the riser's height itself.
HG-1 (Mac N' Cheese V1.5): Laffs Dynamics
First Laffs Dynamics handguard design for the Mac N' Cheese 3DP PCC.
Printer Used: Ender 3 V2
Filament Used: PLA+
Print Settings:
Extruder: 220C
Bed: 56C
First Layer Print Height: .2mm
Standard Layer Height: .16mm
Wall Thickness: .40
Wall Perimeters: 7+
Infill: 75%+
Support Material Percentage: 20%
Notes:
1) This data pack is just for printing the handguard. To get the base firearm data pack, use the following link:
(https://odysee.com/@MiddletonMade:1/MacnCheesev15:d)
Glock Slide Cover Plate CAD Template V1.1: FFFTech/FFFTechnology
STL and STEP files of a Glock slide cover plate template. Able to be easily modified if one wishes for
a specific aesthetic design/texture.
These files are intended to aid in firearm accessory design. Whilst they can be 3D printed, they're mainly
meant to be used in CAD software such as Fusion 360.
Update: Thickened the retention tab by .24mm.
Printer Used: Ender 3 V2
Filament Used: PLA+
Print Settings:
Extruder: 218C
Bed: 56C
First Layer Print Height: .20mm
Standard Layer Height: .12mm
Wall Thickness: .40
Wall Perimeters: 5+
Infill: 32%
Infill Pattern: Gyroid
Material Flow: 100%
A combination of two of my previously designed grips; identical ergonomics of my "Storage AR15 Grip", with the same height of my "Balance Mini Grip". Overall, Lil Chonkers has a wide enough palm swell to fit comfortably into larger hands, whilst still retaining a compact size for transport and storage in smaller spaces and(or) containers.