Making the Lee 401-175 TC for use in 40 Smith and Wesson. In this video, I just show the process of casting, powder coating and loading. Stay tuned for the shooting video. Thanks for Watching. Visit me at: www.thereloadersnetwork.com ... https://www.youtube.com/watch?v=da2q0FlUGa8
A follow-up video about the upper and parts that I won from El Tenda's channel giveaway. The Rise Armament trigger was malfunctioning and I was getting light primer strikes and non-firing rounds with the Kaw Valley trigger and the other lighter trigger springs that I had. Additionally, the hollow point rounds were intermittently hanging up on the feed ramps. I solved all the problems by using a mil-spec lower and running FMJ rounds. After this, both mags ran 100% and the upper was spitting fire.
Thanks again to El Tenda's channel and Koyote Tan for the parts.
...
https://www.youtube.com/watch?v=lOl4fZA175w
This might be the worst LEE APP video on YouTube. I have watched several other good videos and here are a few.
https://www.youtube.com/watch?v=NVb-yczuXsc
https://www.youtube.com/watch?v=YK-1xTzCYv4
https://www.youtube.com/watch?v=RLXaV3JJkK0
https://www.youtube.com/watch?v=GZ4NO42OPt4
https://www.youtube.com/watch?v=GOxNE6xwqUo
...
https://www.youtube.com/watch?v=AE8ozDBAj88
Unboxing and Initial impressions of my recent order from Freedom Munitions. All ammo looks really good, especially the re-manufactured ammo.
...
https://www.youtube.com/watch?v=mDh8RplFkNI
Testing out some 139 grain soft point bullets from PPU in 8mm Mauser. I was using a Yugoslavian model 24/47.
Thanks for Watching.
*** All Shooting done on Safe and Private Range ***
...
https://www.youtube.com/watch?v=3hc_ZRleCts
*******************Please Read Description************************
****Dillon Precision called me back after I filmed this video. I spent several minutes on the phone with a representative who helped me trouble shoot the powder measure. He told me to remove the springs adjust the screw on the bell crank assembly. He told me that sometimes the fail safe rod needed to be adjusted and I could file some material off in the bent areas if it didn't hang straight down. I think it was just a combination of the fail safe rod not having a proper bend and the assembly was too tight and didn't allow the fail safe mechanism to move properly. It seems simple now, but when you take a new piece of equipment out of the box and the pieces are not fitted properly it can be frustrating to determine where the problem lies. Dillon has been overwhelmed with calls and after trying to request a call back for several days, I finally make it through to them. I did have quite a bit of trouble with the powder measure, but I believe the problem to be fixed and it is cranking out some nice ammo.****
Thanks for Watching.
...
https://www.youtube.com/watch?v=f9ZGJM-Dzsg
************FOR ENTERTAINMENT PURPOSES ONLY AND DOES NOT REPLACE PROPER TRAINING**************************************
Basic instruction on the sight alignment and trigger control. This is basic and condensed and not intended for instructional purposes. The presentation is part of a CCDW class curriculum that has been approved by the DOCJT in Kentucky. This part of the actual class includes many hands on demonstrations and will usually last 45 minutes to 1 hour. I am a little out of practice and tried to condense the presentation to 15 minutes or less for this video. Please remember safety first and you are responsible for your actions. Thanks for watching.
*****This is for entertainment purposes only and does not take the place of proper training.******
...
https://www.youtube.com/watch?v=z0yinGsBg7w
Just another Tokarev video featuring the Yugo M57 and a Czech CZ52. I shoot some reloads and Czech surplus ammo. I get excited and shoot my chrono, but luckily it survived.
...
https://www.youtube.com/watch?v=pvqbO2XQM_o