Second part of me overclocking the AMD Threadripper 1950X under water with the single channel memory. Bit late, but better late than never.
...
https://www.youtube.com/watch?v=WItDfAhzAnY
Boot from cold with my new Crucial M500 240GB SSD
PC Specs
intel Core i5 2550K@5ghz
MSI Z77 Mpower
MSI R7970 Lightning BE
Corsair vengance 1600mhz 2x4GB
Be quiet power zone 650w
Crucial M500 240GB SSD
Bitfenix Shinobi
...
https://www.youtube.com/watch?v=zgLPJUM1AeE
In this video i go through how i have set the reverse up on my Hyper MT Nitro. It is set up using the option part listed below as well as a JX Ecoboost CLS6336HV servo. This servo is overkill for the job, but i plan on using a LiFe receiver battery, so i would like to switch over to all high voltage servos.
The is also a running demo of the truck going both forwards and backwards when i am still breaking the engine in at the park. It is still running very rich, but you can see i am able to stop, switch to reverse, go backwards. Then go forwards again.
The reverse does add a lot of extra rotating mass as well as the extra servo, but i think when i am running in the woods it will be useful to have reverse. The engine should have plenty of power once tuned properly as well, so it should still be pretty quick and get into 2nd gear.
Truck Part Number:
Blue HBMT-C30BU
Grey HBMT-C30DG
Engine:
LRP NITRO ENGINE ZR.28 SPEC. 4 PULLSTART 32803
Option Parts I got at the same time as the truck:
HoBao Hyper Mt Reverse Conversion Kit HOP-0102
HoBao Hyper Mt Chassis Support Plate HOP-0101
HoBao Hyper Mt Cnc Spur Gear 32T HOP-0093
HoBao Hyper Mt Wheelie Bar Set HOP-0081
...
https://www.youtube.com/watch?v=XNkKoek_T94
In this video we will find out what happens when you pair a 10900K with the cheapest Z490 board i could find.
This Gigabyte Z490M UD is MATX, uses a 4+2 phase VRM and i picked this board up for £112. I didn't really do much research into getting a board for this, I just set the price low to high, just so i could test the cpu, before buying a better board.
There were a few issues i had with the board running the 10900K
1) XMP didnt work even on 4266 profile 2
2) voltage for cpu was limited 1.3V, i guess this is to protect the weak vrm.
I would recommend spending £40-50 more to get a board with a better vrm for any 10th gen CPU.
System Spec:
Intel Core i9 10900K ES
Gigabyte Z490M UD
Patriot Viper Steel 4400C19
EVGA GT710
Integral 120GB SSD
Super Flower Leadex 1300W
0:00 Look at the board
1:06 Stock run
3:00 Gaming OC Profile
4:40 Advanced OC Profile
5:42 Intel Multicore Enhancment
6:46 Manual OC BIOS Setup
8:09 4.6ghz
9:28 4.7ghz
10:52 4.8ghz and Thoughts
14:18 Final Scores
...
https://www.youtube.com/watch?v=0vwOLo219L0
This screw fell out Cutting my 6s run a bit short. Unfortunately I only had M3 screws in my toolbox, so i had to go back home to replace it.
...
https://www.youtube.com/watch?v=lXNI4SG3H68