Foxeer Arrow V3 FPV Camera Review. The difference between V3 and V2. Settings included at the end of the video. The flight video is actually the Arrow V2 compared to the RunCam Swift because I was unable to get a flight in due to bad winter conditions. The video quality between the V2 and V3 is similar anyway. They have the same image sensor and same lens. So what is the difference between the Foxeer Arrow V2 and V3? Differences are: New improved metal case to replace plastic case. Better mounting holes into the metal case instead of inserts. Slightly wider voltage range 5-40 volts instead of 5-35. Slightly smaller case size. Microphone is still in the front but removed hole in the case for reduced wind noise. And finally the V3 has a blue case among other colors. The Wiring harness and menu board is the same. Same image sensor and same 2.5 mm lens Settings are the same. Product Description from Banggood: http://www.banggood.com/FOXEER-Arrow-V3-2_5mm-600TVL-HAD-II-CCD-PALNTSC-Mini-FPV-Camera-Built-in-OSD-MIC-p-1121696.html FOXEER ARROW V3 Blue addition version, upgraded metal case, perfect design, it support 5~40V input voltatage, built-in OSD(voltage, time, name), voltage detection, flexible OSD programming cable. FOXEER ARROW V3 is the advanced version of FOXEER HS1177, it features great WDR and brilliant image quality. The camera case is made of light metal, which can better survive from vibrations and crashes. Inbuilt MIC, makes the flying experience more immersive. Package includeds: 1x Camera 1x Instruction Manual 1x camera case 1x metal bracket 1x OSD control board 1x 7pin servo cable ... https://www.youtube.com/watch?v=eCBEDDfz1VQ

This is how to make a Fatshark power cable for your FPV goggles. Also information on where to get the barrel connector or plug is included. You can also buy the completed cable from certain vendors. To make a DIY Fat Shark goggle power cable you need a barrel connector and a battery connector such as a JST or XT60 connector. Some soldering is required but is very easy to do. The barrel plug is 5.5mm OD and 2.1mm ID in size. You can get them from Radio Shack (Tip M) or on Ebay. A cable 21.mm barrel to JST connector can be purchase already made from Hobbywireless for about $5 but the homemade ones are so easy to make that I always make my own. Just make sure to solder the red wire from the JST plug to the center hole of the barrel plug. The ground or negative voltage is on the outside ring of the barrel. ... https://www.youtube.com/watch?v=vgJAxdf8-yA

Quick video on installing LED lights on SpaceWalker UMX Plane including how to make your own tiny bright led lights from surface mount LEDs. This could be handy for any small RC aircraft. Also included is a look inside the SpaceWalker. You will notice the circuit board is mounted in a strange angular position. Surface Mount LEDs http://lighthouseleds.com/catalogsearch/result/index/?p=2&q=SMD Like many LEDs these use 20ma of current. Divide your voltage by the current and it will give you the resistance. For example a 1s LiPo: 4.2v/0.020a = 210 ohms. I used 220 ohms. Spacewalker Information: https://www.youtube.com/watch?v=zgyvpYnR7b8 -~-~~-~~~-~~-~- Please watch: "Runcam Owl Plus Camera with Low Light PL0075 Lens Installed for Night FPV RC Flying" https://www.youtube.com/watch?v=J5CrWcX20P8 -~-~~-~~~-~~-~- ... https://www.youtube.com/watch?v=h-_vHRUtS7w

This is a test flight with 3 flight modes on the BeeRotor FC with and Airplane weighing less than 250 grams. Modes are switched remotely with a FrSky Taranis X9D RC radio. Parts List: http://www.rcgroups.com/forums/showpost.php?p=33943051&postcount=2 See previous video on how to setup the three flight modes. https://www.youtube.com/watch?v=X-hN5ICRcsE -~-~~-~~~-~~-~- Please watch: "Runcam Owl Plus Camera with Low Light PL0075 Lens Installed for Night FPV RC Flying" https://www.youtube.com/watch?v=J5CrWcX20P8 -~-~~-~~~-~~-~- ... https://www.youtube.com/watch?v=YXYhC7oORZk