♻ PolyTerra PLA By PolyMaker - Eco-Friendly Filament - Bioplastic 3D Printing Filament | #Shorts #PolyMaker #PolyTerra #PLA #AllVisuals4U #3DPrinting ⚠ This video is made in association with PolyMaker. I was asked to review this new PolyTerra™ PLA filament. Two free spools have been sent to me to make a video about PolyTerra™ PLA filament. Here's my quick review! ? Longer review: https://youtu.be/T7tREQEZ5DU ? Go to https://polymaker.com/polyterra-pla-info/ and use the promo code ALLVISUALS for 10% off for any PolyTerra™ PLA purchase on the EU or US website! ⚠ Can be used multiple times until December 31st 2021! ? https://onetreeplanted.org/ ⏳ Compostability report: ? ISO 14855-1:2012 (conditions: dark room, 58°C±2°C, vessel: compost with microorganisms): - PolyTerra™ PLA degrades 93.6% after 45 days. - PolyLite™ PLA degrades 79.9% after 45 days. - PolyTerra™ PLA degrades ~15% faster than PolyLite™ PLA - The estimated 100% degradation time is less than 100days ? The models i used in this video: ? Seal by Thingiverse user YahooJAPAN (no changes made) ? https://www.thingiverse.com/thing:182266 ? https://www.thingiverse.com/yahoojapan/designs ? https://creativecommons.org/licenses/by/4.0/ ? Whaleshark by Thingiverse user YahooJAPAN (no changes made) ? https://www.thingiverse.com/thing:182338 ? https://www.thingiverse.com/yahoojapan/designs ? https://creativecommons.org/licenses/by/4.0/ ? Chair 'Single Line' by 3DParts4U ? https://cults3d.com/en/3d-model/home/chair-single-line ⚙ My PLA Simplify3D print settings: - ±3000mm/minute (50mm/second) - hotend 185°C | bed 55°C - 250 micron | infill 20% - 3 top layers | 3 bottom layers | 2 outline layers - brass nozzle 0.35mm - extrusion width 0.44mm - retraction 1.00mm - extrusion multiplier 0.95 - coasting 0.30mm - wipe distance off - fan 100% - 20% normal support | 3 layers of 90% dense support Trizone by Sascha Ende Link: https://filmmusic.io/song/466-trizone License: https://filmmusic.io/standard-license

? 3D Printable Grass - Grass 3D Model - 3D Printing Models | #Shorts #AllVisuals4U #3DParts4U #3DPrinting #Grass #3DModel ? Subscribe to my channel: https://www.youtube.com/channel/UC0d-p0Fhqs0cDN2JeVzdg6Q?sub_confirmation=1 Here's some 3D printed grass! It was printed on the side with a small raft below the end plates for better adhesion. ? 3D Printable Grass by Superbeasti (no changes made) ? https://www.thingiverse.com/thing:3504830 ? https://www.thingiverse.com/superbeasti/designs ? https://creativecommons.org/licenses/by/4.0/ ⚙ My PLA Simplify3D print settings: - 3600mm/minute (60mm/second) - hotend 185°C | bed 50°C - 200 micron | infill 15% - 3 top layers | 3 bottom layers | 3 outline layers - brass nozzle 0.35mm - extrusion width 0.40mm - retraction 1.00mm - extrusion multiplier 0.95 - coasting 0.30mm - wipe distance off - fan 100% - no support needed - rafts are recommended ? My website: https://www.3dpartsforyou.com ⚡ Subscribe to my channel AllVisuals4U Shorts: https://www.youtube.com/channel/UC0d-p0Fhqs0cDN2JeVzdg6Q?sub_confirmation=1 ⚡ All playlists of this channel: https://www.youtube.com/channel/UC0d-p0Fhqs0cDN2JeVzdg6Q/playlists?view=1&flow=grid ? Subscribe to my long format channel AllVisuals4U: https://www.youtube.com/channel/UCZ3nn99kwDQSmmHu9ohYoKQ?sub_confirmation=1 ? All playlists of this channel: https://www.youtube.com/channel/UCZ3nn99kwDQSmmHu9ohYoKQ/playlists?view=1&flow=grid ? Funky Logo 12 by TaigaSoundProd Link: https://filmmusic.io/song/8045-funky-logo-12 License: https://filmmusic.io/standard-license