I had 24 packs charged up for an unnervingly warm xmas eve afternoon, and I got tired of the Toothprick after about 6x. I spent the rest (much faster) flying the ol' Emax "Tinyhawk S". It's likely the tune on it that makes it more fun and somehow appropriate for the size of the area I was flying it in, so I flew the nuts off of it until I couldn't see gaddammit! Which is because I smashed it's little face in, as documented at the end of the video. Oh well, it happens. She'll fly again, but she's long overdue for a new frame of some sort. I'm running out of props and I'd rather transplant it onto some kind of carbon with 1103's or something. We shall see. Current config though: FRA: Emax Tinyhawk S Indoor FPV Racing Drone Spare Part 75mm Polypropylene Frame Kit 1-2S AIO: EMAX Tinyhawk S Indoor Drone Part - AIO Flight Controller/VTX/Receiver (VTX Removed) MOT: EMAX 08025 15000KV (from the original stock 1S Tinyhawk) PRO: EMAX Tinyhawk 4 Blade Turtle Mode Avan Propeller CAM: Caddx Beetle CMOS 800TVL FOV 170 4:3 NTSC (Camera Only!, IR filter was also removed) VTX: Caddx FireFly (VTX Only!) 5.8GHz 25mw ANT: URUAV Micro UXII Stubby RHCP Mini FPV Antenna 1.6dBi 5.8GHz BAT: Turnigy Nano-tech 300mah 2S 45~90C Lipo Pack Added JST, 5V Beeper, Silicone Conformal Coating and black glint tape (hopefully I won't lose it with all these mods). I modded the Beetle lens for IR / night vision after removing it from the VTX. I used a VTX from a FireFly, cause it supports SmartAudio. I direct-soldered the "URUAV Micro UXII Stubby RHCP" to the FireFly VTX and secured it between the rear props on the bottom. +0.3g (and growing) of 3M Blenderm tape, Gaffer tape, superglue, welder glue, and hot glue. 33.85g Modded Weight (dry) [+5.5g] 28.35g Stock Tinyhawk S (dry). +1.41g Taller 15000KV Motors +3.00g Turnigy NanoTech 45~90C Batteries (18g each) 2S AUW is 52 grams. Flight duration is 2-3 minutes on the Nano-techs. 8.68g 4x 0802 15500KV (stock 2S) 10.09g 4x 08025 15000KV (stock 1S) Recorded via ground-based DVR; https://www.immersionrc.com/fpv-produ... https://www.immersionrc.com/fpv-produ... https://www.fatshark.com/product/hdo-... https://caddxfpv.com/products/beetle-v1 Music; "Gently Waves" by Takako Minekawa "Maxi On!" by Takako Minekawa "Spin Spider Spin" by Takako Minekawa "Flow In A Tide" by Takako Minekawa Seriously... this label!!!! https://en.wikipedia.org/wiki/Emperor_Norton_Records The Samurai Robot is from RoboCop 3. What? I liked it. ... https://www.youtube.com/watch?v=9hLYTib0Vkw

i don't remember where that southern kid went. what was his name? meurte muertauh.... something. i think he exscaped to canadia... tarday! ... https://www.youtube.com/watch?v=7zoaIDDQX8Q

Helmet Cam - Go Pro Hero Gun Cam - Contour HD First try at dual cameras on the same subject and pip editing. ... https://www.youtube.com/watch?v=5nWfvAeV9zg

One uncut pack... little sleep, allergy headache... 90% humidity. Dat tram tho... been perfectly fine all day. So this is the modded Tinyhawk S... I melted the motor connectors on the back 2 motors, and they won't insert back in anymore. I'll have to see if I can direct-solder or something. Everything else held up. I crashed while the connectors were molten plastic, so they came out and got deformed and warped into mush. This was the 2nd to last flight, with 2 prior where I was doing flips, rolls and look-backs over a couch fire. Cause there was a couch fire. This didn't contribute to any of the melting, though it may have pre-heated things, given the aggressive flying. Tomorrow is raining and repairs anyway. ... https://www.youtube.com/watch?v=X8iLNyIIaYc