0:00 Intro and schematic walkthrough 4:10 Board walkthrough for Transmit Mixer 6:08 Testing the Audio Network 7:17 Testing the I/Q audio signals 9:40 Testing the 0/180 degree audio signals 10:43 Transmit Mixer on the board and some troubleshooting 11:42 Test setup for SSB 12:06 Test setup with HDSDR and signal generator 13:22 Testing SSB at 14 MHz 14:28 Testing SSB at 7 Mhz ... https://www.youtube.com/watch?v=sh80UZA832Q
In this video I solder connections to the SDA and SCL lines on the SA818 board and show the resulting traffic on the scope. Then I use the I2CDriver
https://i2cdriver.com/
To capture traffic between the uController and RDA1846. I also do a quick demo of the I2CDriver itself. The resulting traffic captured is here:
https://github.com/thaaraak/rda1846/blob/master/documents/c2.csv
I did try the Bus Pirate
http://dangerousprototypes.com/docs/Bus_Pirate
but I was unable to capture the traffic (potentially because the I2C bus is running at too high a frequency)
...
https://www.youtube.com/watch?v=xwUeZcSgzIs
In this video I combine the results of the ESP32 Radio video
https://www.youtube.com/watch?v=bOyliyEWw8U
together with the Streaming Audio
https://www.youtube.com/watch?v=NWdemILPp3Y&t=3s
to create a fully headless IoT receiver - controlled by web interface and streaming the demodulated audio over http to a browser
Code is all here
https://github.com/thaaraak/ESP32-WebServer
0:00 Intro and Recap
0:47 Test using the Signal Generator
2:41 Changing the signal Frequency
4:32 Setup in the Radio Room
5:04 Back to the Garage and on the air
6:42 Wrap up for the receiver
7:40 Whats Next?
9:25 Some final 20m contest reception
...
https://www.youtube.com/watch?v=SlqE-FiX18E
In this video I continue the Phaser build and pull together the phase shift network and RF combiner. I then test the lower sideband suppression on the spectrum analyzer.
I did check the manual and the lower sideband suppression should be -35dB down between 800-2800 Hz. I was only getting that between ~1200-1800Hz. That could certainly be related to the replacement FST3257 I put in. I will check again after the transmit stage is complete.
...
https://www.youtube.com/watch?v=MZ1oD8cNzhA
In this video I install the receive switch which completes this build series. I then test receive functionality
...
https://www.youtube.com/watch?v=fkn2m39RLz8
In this video I play around with the AY-3-8910 programmable sound generator using an ESP32 and Arduino Nano
Here's Andy's Github repo
https://github.com/Andy4495/AY3891x/tree/main
The circuit I used in kicad
https://github.com/thaaraak/AY-1-8910-PSG
PDF version of the circuit
https://github.com/thaaraak/AY-1-8910-PSG/blob/main/AY-1-8910-PSG.pdf
The sketches
https://github.com/thaaraak/AY-3-8910-arduino
I got the AY-3 off Aliexpress
https://www.aliexpress.us/item/2255800642521654.html?spm=a2g0o.order_list.order_list_main.55.2b8b1802eyNJJP&gatewayAdapt=glo2usa
Documentation
https://en.wikipedia.org/wiki/General_Instrument_AY-3-8910
https://map.grauw.nl/resources/sound/generalinstrument_ay-3-8910.pdf
0:00 Intro and device background
3:00 Simple demo tune
3:56 Schematic walkthrough
6:15 The bus control lines
8:05 Simple tone example code and demo
11:37 Noise example code and demo
13:51 Obtaining tunes and Tunes demo
16:50 Wrap up
...
https://www.youtube.com/watch?v=aTT8PE99mlA