Purchase latest version of this design including
3d printed bottom frame and motor mount
Belt, bolts, nuts and washers.
https://www.ebay.com/itm/294539062659
Aluminum motor pulley and machined spindle pulley from ABS plastic.
Link will be posted as soon as i get another set of belts delivered.
Meanwhile, buy me a coffee at
https://www.paypal.me/tonynameless
All my 3D Designs
https://www.thingiverse.com/tonycstech/designs
Manuals, Excel forms, Diagrams, blueprints and other files
https://drive.google.com/drive/folders/0Bw8793Ky1h5ZTHdFUHJNSlYyYm8?resourcekey=0-uLm030aZ9or6LZN_Dlaquw&usp=sharing
...
https://www.youtube.com/watch?v=dXhb_4B9rUQ
Replacing piston rings for the first time i my life.
Not much harder then boiling eggs.
Reason: low compression. Acceleration hesitation that i was unable to compensate with tuning the carbs. Cylinders would get flooded on open throttle but not increase RPM even if throttle opens slowly.
Could get up to 60mph very slowly, but not much faster. Making it go faster would just make the bike shake and choke on gasoline.
Adjusting air also did not help.
All those things pointed to cylinder compression test which revealed the root of the problem.
After this, compression was within range, and bike ran like new.
Bike is sold.
Buyer was the happiest man on the planet at that time.
...
https://www.youtube.com/watch?v=OvAUIyCwZgU
Buy me a coffee at
https://www.paypal.me/tonynameless
All my 3D Designs
https://www.thingiverse.com/tonycstech/designs
Manuals, Excel forms, Diagrams, blueprints and other files
https://drive.google.com/drive/folders/0Bw8793Ky1h5ZTHdFUHJNSlYyYm8?resourcekey=0-uLm030aZ9or6LZN_Dlaquw&usp=sharing
...
https://www.youtube.com/watch?v=Au8YGaEQj_4
Any shredder rated with 12=pages that has micro cross-cut will do.
This old shredder i found was cheap (expensive brand new) and works great.
This monster will eat anything. Just make sure to not overheat it and work no more then 15 minutes at the time, allowing 1hr to cool and lubricated each time.
Also, its best to grind in cold environment because plastic is more brittle and brakes rather then stretches. It makes chunks brake easier and will keep the grinder from clogging.
This is especially true for PLA because PLA gets soft too soon when warm.
...
https://www.youtube.com/watch?v=tO13v2f3864
check out my new channel
https://youtube.com/channel/UCvDDbj3qJYg-5FSPFWJxqMw
Buy me some chocolate so i can continue https://www.paypal.me/tonynameless
Pumps come in different suction direction.
Some on the side, some on the front. Pick which one you like.
They are rated 3.7v. I ran it with 5V no problem.
...
https://www.youtube.com/watch?v=zBiSVjBW6xY
Buy me a coffee at
https://www.paypal.me/tonynameless
All my 3D Designs
https://www.thingiverse.com/tonycstech/designs
Manuals, Excel forms, Diagrams, blueprints and other files
https://drive.google.com/drive/folders/0Bw8793Ky1h5ZTHdFUHJNSlYyYm8?resourcekey=0-uLm030aZ9or6LZN_Dlaquw&usp=sharing
...
https://www.youtube.com/watch?v=ZHUyopgOcXg
Windows application that allows you to tweak your 3d print per layer number.
Download link
https://drive.google.com/file/d/0Bw8793Ky1h5ZajMxdXk5NFplbDQ/view
http://umforum.ultimaker.com/index.php?/topic/4185-tweak-at-layer-number-windows-application/
No installation required. Just run the executable.
...
https://www.youtube.com/watch?v=ikwa3nVHrO8