Spec: Hobbywing Max6 160A ESC Surpass Rocket 1650KV 4092 Motor Yeah racing heatsink Power HD 20KG servo Proline badlands Hyper SST motor mount 48T spur 16T pinion Spider centre diff 500K centre diff oil Losi 8ight T battery tray and esc mount 4S Turnigy Heavy Duty 5.0AH 6S Turnigy 5.0AH Flysky GT5 ... https://www.youtube.com/watch?v=MeKHGqKPZT0
Over the past couple of weeks i have built up a small collection of cheap GTX 500 series cards to bench on rainy days.
The cards were all got from CEX and some of them are surprisingly good. Over the next few days, i will have overlocking videos for most or all of these cards.
The cards are:
ASUS GTX580 DCUII £20
ASUS GTX580 DCUII £20
MSI GTX560 Ti 448 Power Edition OC £18
ASUS GTX560 Ti DCUII £20
Zotac GTX560 Ti £20
...
https://www.youtube.com/watch?v=vWY4pJkOpNs
This video is just a quick video testing out the Xray on 6S rather than 4S which i normally run. For the last few years i have been running 17/42 then 18/42. It seems to go very well, it did about 5mph more on grass over the previous setup. Unfortunately this 5AH battery is way too big for this buggy. The weight and size mean it doesn't fit under the body and the suspension setup is not correct. I will be putting it back to 4S or maybe i will get a thinner 6S lipo if i can find one.
Specs:
Xray XB808 with brushless conversion
Surpass 2000KV 4076 motor
120A Hobbyking Beast X-Car ESC
5AH 6S 30-40C
14/43 pin/spur
Diffs oil setup front to rear 30K-500K-30K
Max Motor Temp: 73C
...
https://www.youtube.com/watch?v=KM5m6-5o_oY
An FX8320 Cooled with an Alpenfohn Matterhorn Rev B with push-pull delta 120X38mm, 3900RPM, 192CFM fans for maximum cooling efficiency. The Thermal Paste under was Thermal Grizzly Kryonaut used by top overclockers around the world. The CPU is in a Asus CVFZ motherboard and is currently at 4.7ghz on 1.45v.
Thanks For watching!
...
https://www.youtube.com/watch?v=2C7BCPGNgUA
How to replace the thermal paste on your GPU. this HD6950 only used 4 screws in the heatsink, so it was fairly easy.
Tips:
Check that you have taken all of the screws out before trying to remove the cooler or it wont end well.
Use the correct size screw driver to avoid stripping the heads.
Take pics or video the dis assembly process, so that you dont forget where each screw or washer should go.
Check your warranty to make sure it won't be invalid by taking the heatsink off.
Make sure you disconnect fans before pulling the heatsink off fully.
I would recommend replacing the thermal pads if they are very dirty or damaged, but make sure you get the correct thickness of pad.
...
https://www.youtube.com/watch?v=Auhbz0iK4ds
In this video i take a closer look at the custom Exhaust hanger i have made for the Hyper MT Nitro before running it.
During my run i have seen that there seems to be oil around the rear of the engine and the truck is not responding well to tuning.
Any idea of what i could do to fix this or trouble shooting steps i can do please put them in the comments below.
...
https://www.youtube.com/watch?v=ZlmWsmsS6Ys
This video was from the 19/07/2020. I held it back to give Hobao a change to respond which they haven't. There will also be a more recent follow up upload straight after this, so please watch that as well.
Well this is disappointing. Hobao Hyper MT Sport Plus Nitro universal drive shaft issues. They are actually broken from new.
...
https://www.youtube.com/watch?v=fnoBLGvPV74