If you would like to support my work, BTC donations accepted at 386wAjoV9QqSkpV2Qc7HdqG7b4BW8XVFfx
The 19X is a 19 slide on a 17 grip with my V2 frame style... idk blame PSR. Anyways this is still a beta and hasn't been tested yet so if you print this before I actually release it you may just die or whatever. If that doesn't turn you off... thanks for helping me test!
BTC donation address 386wAjoV9QqSkpV2Qc7HdqG7b4BW8XVFfx
This work is licensed under a GNU General Public License v2.0
✖ | Sharing without ATTRIBUTION
✔ | Remix Culture allowed
✔ | Commercial Use
✔ | Meets Open Definition
ℹ | Share under the same license
If you would like to support my work, BTC donations accepted at 386wAjoV9QqSkpV2Qc7HdqG7b4BW8XVFfx
THIS FILE IS A BETA IT HAS NOT BEEN RELEASED AND IS MAY BE UPDATED/CHANGED WITHOUT WARNING AT ANY POINT BEFORE RELEASE
If you would like to support my work, BTC donations accepted at 386wAjoV9QqSkpV2Qc7HdqG7b4BW8XVFfx
This is the V2 Beta for the Chairmanwon Glock 19. THIS IS A BETA IT MAY NOT WORK RIGHT AND WILL PROBABLY HAVE PROBLEMS. With that said, thank you for helping me test it!
BTC donations accepted at 386wAjoV9QqSkpV2Qc7HdqG7b4BW8XVFfx
This work is licensed under a GNU General Public License v2.0
✖ | Sharing without ATTRIBUTION
✔ | Remix Culture allowed
✔ | Commercial Use
✔ | Meets Open Definition
ℹ | Share under the same license
BTC donation address 386wAjoV9QqSkpV2Qc7HdqG7b4BW8XVFfx
Glock 19 with 10 new stipple patterns for open testing
This work is licensed under a GNU General Public License v2.0
✖ | Sharing without ATTRIBUTION
✔ | Remix Culture allowed
✔ | Commercial Use
✔ | Meets Open Definition
ℹ | Share under the same license
.1 Update is up
-Mag release spring hole corrected, 1mm less deep
-New stipples added
CHAIRMANWON GLOCK V3
-------------------------------------------------------------------
Files are not released under any liscense. Commercial use is not premitted without my express consent.
-------------------------------------------------------------------
BTC donation address 386wAjoV9QqSkpV2Qc7HdqG7b4BW8XVFfx
-------------------------------------------------------------------
website can be found at origamifaceshield.com chairmanwon.com or chairmanjuan.com
-------------------------------------------------------------------
Consult print orientation PDF for best results
-------------------------------------------------------------------
DO NOT USE ANY NOZZLE LARGER THAN .4mm. THERE WILL BE HOLES IN THE PRINT IF YOU DO
-------------------------------------------------------------------
Printing Profile Notes
Support X/Y Distance: 1.3mm (stops Cura from supporting stipples)
Use tree supports instead of normal supports (if you are suffering from very long slice times switch back to normal supports, you will waste material compared to trees but the print will be fine)
Enable Z hop on retract
If you are using Prusa Slicer make sure you have Detect Thin Walls set to off
Nozzle: 0.4mm
Layer Height: 0.16mm
Temp: 215-230/60C
Infill: 100%
Walls: 8
Supports: On/full - use a close support interface gap. Your interface gap should not be larger than 0.15mm unless you know what you are doing with your setup.
Cooling: As low as you can get away with for your printer
All other settings can/should be left as default or whatever you know works best with your printing setup.
CHAIRMANWON'S STIPPLED GLOCK GOTY
-------------------------------------------------------------------
Files are licensed under GPL2
AKA feel free to use these files for any puropose (including commercial) but you have to attribute them to me and any derivitives must be released under the same license if you release it.
-------------------------------------------------------------------
BTC donation address 386wAjoV9QqSkpV2Qc7HdqG7b4BW8XVFfx
-------------------------------------------------------------------
website can be found at origamifaceshield.com chairmanwon.com or chairmanjuan.com
-------------------------------------------------------------------
Print these files rails up or down for best results. I know you see me printing at 45 degrees from time to time, but don't do that and expect the best results
-------------------------------------------------------------------
Printing Profile Notes
Support X/Y Distance: 1.3mm (stops Cura from supporting stipples)
Use tree supports instead of normal supports (if you are suffering from very long slice times switch back to normal supports, you will waste material compared to trees but the print will be fine)
Enable Z hop on retract
If you are using Prusa Slicer make sure you have Detect Thin Walls set to off
Nozzle: 0.4mm
Layer Height: 0.16mm
Temp: 215-230/60C
Infill: 100%
Walls: 8
Supports: On/full - use a close support interface gap. Your interface gap should not be larger than 0.15mm unless you know what you are doing with your setup.
Cooling fan: 20% normal, 50% on bridges. Off for the first 3 layers. Keep the fan low to prevent warp.
All other settings can/should be left as default or whatever you know works best with your printing setup.
BTC donation address 386wAjoV9QqSkpV2Qc7HdqG7b4BW8XVFfx
This work is licensed under a GNU General Public License v2.0
✖ | Sharing without ATTRIBUTION
✔ | Remix Culture allowed
✔ | Commercial Use
✔ | Meets Open Definition
ℹ | Share under the same license
BTC donation address 386wAjoV9QqSkpV2Qc7HdqG7b4BW8XVFfx
This work is licensed under a GNU General Public License v2.0
✖ | Sharing without ATTRIBUTION
✔ | Remix Culture allowed
✔ | Commercial Use
✔ | Meets Open Definition
ℹ | Share under the same license