Published By
Created On
9 Oct 2021 00:10:37 UTC
Transaction ID
Cost
Safe for Work
Free
Yes
Lidl Parkside Inspection Camera Endoscope PKI 2.7 A1Quick Review
A quick review of the Lidl Parkside inspection camera/endoscope PKI 2.7 A1.
It can show you live video, and take stills. It has memory of 7MB and takes JPG files at 640 x 480 resolution. Currently in Lidl for £39.99.
...
https://www.youtube.com/watch?v=7hjGr3N7eOE
It can show you live video, and take stills. It has memory of 7MB and takes JPG files at 640 x 480 resolution. Currently in Lidl for £39.99.
...
https://www.youtube.com/watch?v=7hjGr3N7eOE
Author
Content Type
Unspecified
video/mp4
Language
English
More from the publisher
Controlling
VIDEO
LONDO
london-to-brighton-veteran-car-run-19
London To Brighton Veteran Car Run 2023 Short 7 #car #veteran #shorts #short
More to come!
Link to full video, part 1
https://www.youtube.com/watch?v=FU1IBefI1Ds
Link to part 2.
https://www.youtube.com/watch?v=BFHrg8WPtCU
...
https://www.youtube.com/watch?v=AwstvDK1JMk
Transaction
Created
1 month ago
Content Type
Language
video/mp4
Controlling
VIDEO
LIDL
lidl-parkside-cordless-impact-drill
Lidl Parkside Cordless Hammer Drill PSBSA 20-Li B2 Review
A fairly handy cordless hammer drill, available bare, (without battery or charger) from Lidl for £19.99.
...
https://www.youtube.com/watch?v=qRKsg6l0pCE
Transaction
Created
1 month ago
Content Type
Language
video/mp4
English
Controlling
VIDEO
STIRL
stirling-engine-running-on-methylated
Stirling Engine running on Methylated spirits at Brighton Model world on the Mid Sussex Model Engineering club stand.
...
https://www.youtube.com/watch?v=KaMps4SXRIU
Transaction
Created
1 month ago
Content Type
Language
video/mp4
Controlling
VIDEO
PETTE
petter-paz1-setting-adjusting-the
Setting the decompressor on a later type Petter PAZ1,
Note that just before I made this video I had to use a vice, hammer and spanner to loosen the lock nut. I thought I had put it back to the same place but hadn't which is why I was surprised at the compression I had at the start of this video.
...
https://www.youtube.com/watch?v=DI9NzJwqlBw
Transaction
Created
1 month ago
Content Type
Language
video/mp4
English
Controlling
VIDEO
FIXIN
fixing-runout-on-a-drill-press
In a previous video (linked below) I made a flywheel puller for a wacker rammer on my Naerok mill/drill. There was a tremendous amount of runout which caused a centre drill to break. Not a problem with collletts, just chucks.
Here I check the runout in a chuck and fix it. Turned out to be the taper on the arbor in the Triangle brand Chinese made chuck that came with the mill drill.
https://www.youtube.com/watch?v=LktUYTIsD4c
...
https://www.youtube.com/watch?v=jUuYp8dsM1A
Transaction
Created
1 month ago
Content Type
Language
video/mp4
English
Controlling
VIDEO
LONDO
london-to-brighton-veteran-car-run-13
London To Brighton Veteran Car Run 2023 Part 2
Featuring all sorts of cars including a lot made before 1905. Also has steam cars in it too!
...
https://www.youtube.com/watch?v=BFHrg8WPtCU
Transaction
Created
1 month ago
Content Type
Language
video/mp4
English
Controlling
VIDEO
FINDI
finding-and-fixing-the-noise-in-an
Finding and fixing the noise in an induction motor (Single phase Crompton Parkinson) with a bit on how the centrifugal switch works.
0:00 Introduction
0:30 Demonstrating the noise
1:25 Taking the motor apart
5:30 Removing rotor
5:50 Showing the fault
6:45 Fixing the fault
7:32 Showing how the centrifugal switch works
8:26 Reassembly
13:40 Fitting the pulley and key
15:30 Final testing
16:00 Conclusion
...
https://www.youtube.com/watch?v=0BrGVqA-WOI
Transaction
Created
1 month ago
Content Type
Language
video/mp4
English
Controlling
VIDEO
JAM J
jam-jar-pulse-jet-methanol
Just a jam jar pulse jet running on methylated spirits
...
https://www.youtube.com/watch?v=ZN7VfD7flik
Transaction
Created
1 month ago
Content Type
Language
video/mp4
Controlling
VIDEO
MAKIN
making-a-spanner-extension-(when-you
Trying to replace the power steering pump on my Jaguar X Type deisel, I ran into a problem I have had before. The high pressure union refuses to split.
Well, sometimes you just need a bigger tool....
Here is how I make a spanner extension to turn my 8 inch spanners to 30 inch spanners.
0:00 Introduction and explanation of the problem
0:30 Showing the solution
1:30 Showing the spanner Extension in use
2:40 Drilling
7:19 Making the buttons on the lathe (start)
15:30 Parting off.
18:56 Facing the buttons
22:20 Welding in the buttons
28:11 Welding in the handles
33:27 Cleaning off the Welding slag
33:45 Grinding the edges round
34:06 Conclusion
...
https://www.youtube.com/watch?v=7o0NJcVKVkE
Transaction
Created
1 month ago
Content Type
Language
video/mp4
English