Micro Motor Warehouse CL-0615-14 coreless motor https://micro-motor-warehouse.com/collections/all-motors/products/cl-0615-14 I still think these motors require more break-in time. These were more NOS parts I had from my busted Rakon-framed Inductrix. So far they don't feel all that different to the stock H8 motors. I have some -17's on the way to test. ($2.50/4 on clearance from airblade) I was hoping for some improvement, but so far the only blatantly noticeable factor has been the Silverware firmware mod itself. The search continues for the ultimate ~25g freestyle FPV quad. The props are in view, so figure it out (though this vid is more for my reference); 1: "Gemfan 50mm" / "Blade Nano QX" prop; really wobbly. They lack punch, and response. I suspect they have more angular momentum, so it would need to be tuned differently. The last quarter of the throttle would cause dipping. https://www.banggood.com/4-Pairs-Gemfan-50mm-ABS-Propellers-For-80-100-Class-Frame-Kits-6-8mm-Coreless-Motors-p-991023.html?akmClientCountry=America&rmmds=cart_middle_products&cur_warehouse=CN 2: "Eachine E57" / "45mm HK Pocket-Quad" prop; less wobbly. They have better punch than the nanoQX, but they feel heavy like they brake less quickly than the stock H8 prop. They wash out more easily, and the top of the throttle range is unpredictable (likely tuning issue). ... https://www.youtube.com/watch?v=eLQnq9egLkM

I had 24 packs charged up for an unnervingly warm xmas eve afternoon, and I got tired of the Toothprick after about 6x. I spent the rest (much faster) flying the ol' Emax "Tinyhawk S". It's likely the tune on it that makes it more fun and somehow appropriate for the size of the area I was flying it in, so I flew the nuts off of it until I couldn't see gaddammit! Which is because I smashed it's little face in, as documented at the end of the video. Oh well, it happens. She'll fly again, but she's long overdue for a new frame of some sort. I'm running out of props and I'd rather transplant it onto some kind of carbon with 1103's or something. We shall see. Current config though: FRA: Emax Tinyhawk S Indoor FPV Racing Drone Spare Part 75mm Polypropylene Frame Kit 1-2S AIO: EMAX Tinyhawk S Indoor Drone Part - AIO Flight Controller/VTX/Receiver (VTX Removed) MOT: EMAX 08025 15000KV (from the original stock 1S Tinyhawk) PRO: EMAX Tinyhawk 4 Blade Turtle Mode Avan Propeller CAM: Caddx Beetle CMOS 800TVL FOV 170 4:3 NTSC (Camera Only!, IR filter was also removed) VTX: Caddx FireFly (VTX Only!) 5.8GHz 25mw ANT: URUAV Micro UXII Stubby RHCP Mini FPV Antenna 1.6dBi 5.8GHz BAT: Turnigy Nano-tech 300mah 2S 45~90C Lipo Pack Added JST, 5V Beeper, Silicone Conformal Coating and black glint tape (hopefully I won't lose it with all these mods). I modded the Beetle lens for IR / night vision after removing it from the VTX. I used a VTX from a FireFly, cause it supports SmartAudio. I direct-soldered the "URUAV Micro UXII Stubby RHCP" to the FireFly VTX and secured it between the rear props on the bottom. +0.3g (and growing) of 3M Blenderm tape, Gaffer tape, superglue, welder glue, and hot glue. 33.85g Modded Weight (dry) [+5.5g] 28.35g Stock Tinyhawk S (dry). +1.41g Taller 15000KV Motors +3.00g Turnigy NanoTech 45~90C Batteries (18g each) 2S AUW is 52 grams. Flight duration is 2-3 minutes on the Nano-techs. 8.68g 4x 0802 15500KV (stock 2S) 10.09g 4x 08025 15000KV (stock 1S) Recorded via ground-based DVR; https://www.immersionrc.com/fpv-produ... https://www.immersionrc.com/fpv-produ... https://www.fatshark.com/product/hdo-... https://caddxfpv.com/products/beetle-v1 Music; "Gently Waves" by Takako Minekawa "Maxi On!" by Takako Minekawa "Spin Spider Spin" by Takako Minekawa "Flow In A Tide" by Takako Minekawa Seriously... this label!!!! https://en.wikipedia.org/wiki/Emperor_Norton_Records The Samurai Robot is from RoboCop 3. What? I liked it. ... https://www.youtube.com/watch?v=9hLYTib0Vkw