LED Matrix Lamp made with a Budget 3D Printer [ANet ET4+]
This video shows a short test of the ANet ET4+ 3D Printer. It provides some cool features that allow continuing after power off and changing the filament mid-print. I tested the filament change to print a functional lamp case for a simple 16x16 pixel RGB LED matrix. The lamp is driven by the ESP8266 and WLED. It can be controlled over WiFi and used for several IoT purposes.
This video shows an affordable way to add USB support to maker projects.
$2 for 10 PCBs (Any Color): https://jlcpcb.com (sponsor)
The CH559 is a 8051 architecture based microcontroller that has built in dual USB Hosts. This allows to interface generic Keyboards, Mice, MIDI devices and in my case gamepads. I added this chip as an add on to my ESP32 based game console to replace the SNES controllers by cheap generic ones. The communications is handled over UART which can be done by both ends in hardware. There still is some work to do but you can try it out already. Have fun!
CH559 firmware sources & compiler:
https://github.com/atc1441/CH559sdccUSBHost
Aarons video:
https://youtu.be/Th88RiSmj2w
Links to my game using the USB:
https://github.com/bitluni/GameWing2USB
CH559:
https://link.bitluni.net/ch559
Links to the parts (affiliate links):
USB SNES Gamepad ($2.70 shipped):
USB Fake PS3 Controller ($3.30 shipped):
https://aliexpress.bitluni.net/usbPs3
https://aliexpress.bitluni.net/usbSnes
Set of Tweezers ($3):
https://aliexpress.bitluni.net/tweezers
Flux ($3 for two):
https://aliexpress.bitluni.net/flux
Ultrasonic Cleaner(~$50):
https://aliexpress.bitluni.net/cleaner
Soldering Mat ($9):
https://aliexpress.bitluni.net/mat
My camera and lens (4k 60fps):
https://amazon.bitluni.net/gh5
plz share :-)
Check out my Tindie store to get some of my creations:
https://www.tindie.com/stores/bitluni
Consider supporting my lab for some extras and frequent updates:
https://github.com/sponsors/bitluni
https://www.patreon.com/bitluni
https://paypal.me/bitluni
Twitter: @bitluni
reddit: u/bitluni
#electronics #diy #maker
...
https://www.youtube.com/watch?v=po3FBdY0GS4
A new speed controller improves my DIY electric scooter to support regenerative braking and battery protection. The VESC provides a ton of options to control the hub motor. A simple analog stick is used a throttle now. Enjoy!
Links to the parts (affiliate links):
VESC:
https://aliexpress.bitluni.net/vesc
https://ebay.bitluni.net/vesc
https://amazon.bitluni.net/vesc
https://hobbyking.bitluni.net/vesc
Sensor Kit (including analog stick):
https://aliexpress.bitluni.net/sensorKit
5.5" Hub motor 250W:
https://aliexpress.bitluni.net/miniHubMotor
3S LiPo:
https://amazon.bitluni.net/3S4Ah
https://ebay.bitluni.net/3S4Ah
2mm JST PH:
https://aliexpress.bitluni.net/jst2mm
XT Connectors:
https://aliexpress.bitluni.net/xt
Clampmeter:
https://amazon.bitluni.net/clamp
Action Cam:
https://aliexpress.bitluni.net/actionCam
https://amazon.bitluni.net/actionCam
My camera and lens (4k 60fps):
https://amazon.bitluni.net/gh5
Config tool for esc:
https://vesc-project.com/
plz share :-)
Consider supporting my lab on Patreon for some extras and frequent updates:
https://www.patreon.com/bitluni
I'm also thankful for any donation on PayPal:
https://paypal.me/bitluni
Check out my Tindie store to get some of my creations:
https://www.tindie.com/stores/bitluni
Twitter: @bitluni
reddit: r/bitluni
#electronics #diy #electricscooter
...
https://www.youtube.com/watch?v=OZFbep8wG7E
Footage from Maker Faire Berlin 2017.
plz share :-)
Consider supporting our work on Patreon for some extras:
https://www.patreon.com/bitluni
We are also thankful for any donation on PayPal:
https://paypal.me/bitluni
...
https://www.youtube.com/watch?v=EL2ZwFq_pWo
In this video we upgrade a basic doorbell to send notifications over WiFi. With some power harvesting no battery is required. An optional Node-RED server translates the signal and activates a visual notification remotely. This not only helps if the bell isn't audible but can also be use for hearing disabled people.
Code and Noder-RED flow can be found here:
https://github.com/bitluni/Doorbell
Links to parts and tools (affiliate links):
ESP8266 D1 Mini ($3.50): https://aliexpress.bitluni.net/d1mini
Flexible RGB LED Matrix ($12.20): https://aliexpress.bitluni.net/flexRGB
AC to DC PSU with Barrel Jack: https://aliexpress.bitluni.net/ACtoDCBarrel
Small DC-DC Converter: https://aliexpress.bitluni.net/smallDC2DC
Electrolytic Capacitors: https://aliexpress.bitluni.net/elco
Zener Diode Set ($4): https://aliexpress.bitluni.net/zener
Full Bridge Rectifiers: https://aliexpress.bitluni.net/fbr
My camera and lens (4k 60fps):
https://amazon.bitluni.net/gh5
Zoom H6 Audio Recorder:
https://amazon.bitluni.net/h6
plz share :-)
Tindie store: https://www.tindie.com/stores/bitluni
Github Sponsors: https://github.com/sponsors/bitluni
Patreon: https://www.patreon.com/bitluni
Channel membership: https://www.youtube.com/channel/UCp_5PO66faM4dBFbFFBdPSQ/join
Paypal: https://paypal.me/bitluni
Dogecoin: DLhdK867hZCvuPqmpgviZqgfvUTdSiRfoU
bitclout: https://bitclout.com/u/bitluni
Twitter: @bitluni
reddit: u/bitluni
Discord: https://discord.gg/MT5RbJt
Music:
Jeremy Blake - Powerup!
Wayne Jones - Brain Trust
Quincas Moreira - Sparse Clouds
#electronics #maker #iot
...
https://www.youtube.com/watch?v=NP7_cPEDocI
This Ping Pong LED Wall is made of large PCBs sponsored by: PCBWay https://www.pcbway.com/?from=bitluni
It consists of 1920 ping pong balls as pixels and is controlled by an ESP32. The parallel data lines allow over 74fps and a camera live feed. The panels are easy to exchange in case of failure and built in bus lines and configurable mounting plates allow to build a display of any shape. My Arduino library provides the LED driver and a graphics interface to draw and display anything.
Mike Harrisons talk: https://youtu.be/5SQt1f4PsRU
ESP32Lib Arduino library (camera and nyancat are in the exmples): https://github.com/bitluni/ESP32Lib
SK6812 Datasheet: http://www.normandled.com/upload/201805/SK6812RGBX-XX%20Datasheet.pdf
My store: https://www.tindie.com/stores/bitluni/
Links to parts and tools (affiliate links):
ESP32 Cam: https://aliexpress.bitluni.net/espCam
ESP32-Cam Programmer: https://link.bitluni.net/camProg
RGBW LED Strips: https://aliexpress.bitluni.net/sk6812strip
Individual SK6812 RGBW LEDs: https://aliexpress.bitluni.net/sk6812
Ping Pong Balls: https://aliexpress.bitluni.net/pingPong
Meanwell HLG-600H-24A Powersuppply: https://amazon.bitluni.net/600H24A
12/24 to 5V Power supplies: https://aliexpress.bitluni.net/24to5
WAGO Nuts/Clamps: https://amazon.bitluni.net/wago
KF2510 Connector Set: https://aliexpress.bitluni.net/kf2510
RGB LED chain lights: https://aliexpress.bitluni.net/wiredRgbLeds
Clampmeter: https://amazon.bitluni.net/clamp
Makita Brushless Drill: https://amazon.bitluni.net/makitaBL
My camera and lens (4k 60fps):
https://amazon.bitluni.net/gh5
Zoom H6 Audio Recorder:
https://amazon.bitluni.net/h6
plz share :-)
Tindie store: https://www.tindie.com/stores/bitluni
Github Sponsors: https://github.com/sponsors/bitluni
Patreon: https://www.patreon.com/bitluni
Channel membership: https://www.youtube.com/channel/UCp_5PO66faM4dBFbFFBdPSQ/join
Paypal: https://paypal.me/bitluni
Twitter: @bitluni
reddit: u/bitluni
Discord: https://discord.gg/MT5RbJt
Music:
Jeremy Blake - Powerup!
Eveningland - Escape
Andrew Langdon - Keys
Vibe Mountain - Operatic 3
Wayne Jones - Brain Trust
Andrew Langdon - Follow Me
Dan Henig - Orange Foot
Jingle Punks - Choose Your Path
Myuu - Falling Rain
#rgb #LED #maker
...
https://www.youtube.com/watch?v=EZEMK-C-nSo
In the final part of the retro GAME BOY clone build we fix some sound problems and the scaling on the old school mini CRT. Some on board trimmers end up being very useful to give it the final edge. The SpaceX themed Tetris clone works now nicely with the device. It's a ton of fun failing difficulty 9-5 :-D
Check out the complete playlist to see the complete build:
https://www.youtube.com/watch?v=ls8FfGh718Q&list=PLjUbKCHhzPEyK-5oT1tVXNWXiBj9pNJZs
ESP32 Game console playlist for the essentials:
https://www.youtube.com/watch?v=5t1_XNc3vNw&list=PLjUbKCHhzPEzCm2_KFAICIN-7QTap_s72
The latest schematic and some further details are provided here:
http://bitluni.net/crt-boy/
The Tetris clone code for the ESP32:
https://github.com/bitluni/TetrisSpaceX
The final ESP32 I used here (affiliate link):
ESP Mini KIT ~$7.58 shipped http://s.click.aliexpress.com/e/FQ7mQRJ
plz share :-)
Consider supporting my lab for some extras and frequent updates
trough YouTube Memberships https://www.youtube.com/channel/UCp_5PO66faM4dBFbFFBdPSQ/join
or on Patreon https://www.patreon.com/bitluni
I'm also thankful for any donation on PayPal:
https://paypal.me/bitluni
Twitter: @bitluni
Instagram: @bitluni
reddit: u/bitluni
#retro #gameboy #electronics #esp32 #tetris #spacex
...
https://www.youtube.com/watch?v=Epc0nvDWjvg
This version of my legendary Ping Pong LED Wall is 2x1,5m in size and consists of 1200 RGB LEDs. The build is done from aluminium using a DIY hole punch. This version is driven by an ESP32 and supports even camera streaming from an ESP32Cam or media streaming from the PC. More on that topic follows in a future update.
Links to the parts (affiliate links):
LEDs $8 a set RGB
https://aliexpress.bitluni.net/wiredRgbLeds
Balls 150pcs for $7
https://aliexpress.bitluni.net/pingPong
70A 5V Power Supply $22
https://aliexpress.bitluni.net/70Apsu
ESP32 Mini KIT $4.50:
https://aliexpress.bitluni.net/ESP32mini
ESP32 Cam $5:
https://aliexpress.bitluni.net/espCam
My camera and lens (4k 60fps):
https://amazon.bitluni.net/gh5
AC/DC TIG Welders:
https://amazon.bitluni.net/tigWelders
plz share :-)
Check out my Tindie store to get some of my creations:
https://www.tindie.com/stores/bitluni
Consider supporting my lab on Patreon for some extras and frequent updates:
https://www.patreon.com/bitluni
I'm also thankful for any donation on PayPal:
https://paypal.me/bitluni
Twitter: @bitluni
reddit: r/bitluni
#diy #maker #neopixel
...
https://www.youtube.com/watch?v=xFh8uiw7UiY
Follow up video how to configure two HM-10 (and higher) modules to communicate over Bluetooth. The two base modes of the HM firmware are explained:
1. Transmission mode sending all incoming UART data to the UART of the other module
2. Remote control mode sensing and controlling the IO pins of the other module
IMPORTANT NOTE: You might need to send AT+CLEAR to pair the master to another HM-10 module, once it was paired.
Tune in for some practical mini projects using this features and more videos that will spot on implementing own firmware.
...
https://www.youtube.com/watch?v=nliVeSmpFgg
It's time to share my experience I made with my new ANYCUBIC 3D printers. These are monochromatic TFT based resin printers really surprised me with the level of detail and print speed. The best part is that I can print transparent stuff that is suitable to be used as optics. I'did quite some experiments and am happy to share it here with you.
Anycubic sponsors the hardware so check out their special offers:
Mono: https://bit.ly/3mbVj45
Mono SE: https://bit.ly/3ncKZdC
Wash and cure 2.0:https://bit.ly/2KgEMi1
Links to parts and tools (affiliate links):
My camera and lens (4k 60fps):
https://amazon.bitluni.net/gh5
Zoom H6 Audio Recorder:
https://amazon.bitluni.net/h6
plz share :-)
Tindie store: https://www.tindie.com/stores/bitluni
Github Sponsors: https://github.com/sponsors/bitluni
Patreon: https://www.patreon.com/bitluni
Channel membership: https://www.youtube.com/channel/UCp_5PO66faM4dBFbFFBdPSQ/join
Paypal: https://paypal.me/bitluni
Twitter: @bitluni
reddit: u/bitluni
Discord: https://discord.gg/MT5RbJt
Music:
Jeremy Blake - Powerup!
Andrew Langdon - Follow Me
Dan Henig - Orange Foot
Andrew Langdon - Keys
#maker #3dprinting
...
https://www.youtube.com/watch?v=W0fqwLYsuS4