I took off this short especially for all the skeptics. Self-made petal disk for a gasoline trimmer for the second year in operation. Yes, it's a little run-down, but it works and mows a lot.
Video of its creation:
https://youtu.be/6TVcBHtHOSI
Спеціально для всіх скептиків зняв цей шорт. Саморобний лепестковий диск для бензотримера другий рік в роботі. Так, трохи покоцаний, але працює, і косить не мало.
Відео його створення https://youtu.be/6TVcBHtHOSI
...
https://www.youtube.com/watch?v=115EjoGbakM
Do-it-yourself ceramic heater with automatic temperature control XH-W3001.
An economical heater for your home.
How to make a ceramic heater yourself.
Cold winter workshop. It is necessary to somehow warm it up.
For this I will make a ceramic heater.
Of course, you can buy, but this is not our method.
For this I will need - one ceramic granite tile measuring 60 x 60 cm.
16 meters of carbon heating cable with a resistance of 33 ohms per meter.
4 furniture steel corners.
Thermoregulator XH-W3001 or some other.
A couple of meters of electrical cable and a plug.
4 furniture pins and nuts, you can also have grovers if you wish.
It is also necessary to buy a diamond drill for ceramic tiles.
And this is a copper tube 30 cm long, it can be aluminum.
It is advisable to have a hot glue gun.
Reinforcing mesh, 1 meter.
Mixture for pouring a warm floor, you need 1/3 of a bag.
The corners need to be shortened a little and larger holes should be drilled.
It is not convenient to make such a hole with a drill
Then he switched to the machine, the hole turned out perfect.
The main thing is not to overheat the drill.
I roll the copper tube well from one end.
Then it's time to install the thermal cable.
I will make two contours of 8 meters each.
I will connect them in parallel.
The scheme is approximately as follows.
First, I will tape the cable, and then I will fix it better with hot glue.
Somehow...
It works, you can pour concrete :).
I wrap the formwork with ordinary transparent tape so that the solution does not stick to the boards
"Recipe" of the filling mixture.
I will use 1/3 of a 25 kilogram bag.
Attention, eyes!!! :)
I hit the seam between the bricks, then I had to redrill a couple of centimeters higher.
The power is approximately 350 watts.
The temperature of the panel at the moment is on the scoreboard.
I set the working temperature range.
The design works, you can make a couple more of these...
Cost - tile 60x60 cm (4.9USD), mixture (1.1USD), thermostat (2.5USD), heating cable (5USD), corners (1USD), bolts (0.5USD), power cord and plug (1USD), dowel-hooks (0.4USD), grid (0.5USD), hot-melt glue (0.5USD) - total 17.4 USD
Like, share, comment and subscribe to my channel!
Thank you for viewing!
Instagram: @madeingarage1
Facebook: https://facebook.com/groups/1113008455830620/
Email: migdiy2020@gmail.com
...
https://www.youtube.com/watch?v=E_4j9Ua2kiU
A simple tool for every workshop.
Cutter, chisel, резак, долото
Thank you!
Good luck!
Contact me: migdiy2020@gmail.com
...
https://www.youtube.com/watch?v=aPlVJRZ6730
Repair of the Volkswagen Transporter T4 car - process of manufacturing of the kaprolon plug of a directing side door on the lathe. Dismantling of the old spare part and its replacement with a new one. Work for a small lathe. Simple turning work. Dimensions of the sleeve with drawings.
My Instagram:
https://www.instagram.com/madeingarage1/
...
https://www.youtube.com/watch?v=q66Wt-g6iOQ
A tool for a grinder to remove rust from metal and clean it
Attachment for a grinder for cleaning metal. How to remove rust from the surface of old metal. A machine for cleaning metal from impurities. An interesting machine for an angle grinder. How to improve your angle grinder. A new life for an old angle grinder.
...
https://www.youtube.com/watch?v=4LwO3GKmcz0
Friends, hello everyone!
In this video, I make a two-in-one design. Namely - the cart for the welding machine is combined with a table for the drilling machine (drill press stand). The design moves on small rotary wheels. Everything is done on the day of saving space in my workshop.
Thank you for viewing!
Good luck in everything!
Contact me: migdiy2020@gmail.com
My Instagram:
https://www.instagram.com/madeingarage1
...
https://www.youtube.com/watch?v=fPNwLn7WH5s