Published By
Created On
23 Feb 2021 07:22:34 UTC
Transaction ID
Cost
Safe for Work
Free
Yes
u-Link NAND program Openwrt on Meraki MR33.
The 3.3v to NAND only draw 90mA. So the power is directly from the u-Link NAND.
Program the openWRT on MR33 only need to replace the u-boot (2012 version) and ubi. The process is easy and fast.(about 10 min)
...
https://www.youtube.com/watch?v=8nCkiAG1Dsw
Program the openWRT on MR33 only need to replace the u-boot (2012 version) and ubi. The process is easy and fast.(about 10 min)
...
https://www.youtube.com/watch?v=8nCkiAG1Dsw
Author
Content Type
Unspecified
video/mp4
Language
English
More from the publisher
Controlling
VIDEO
U-LIN
u-link-nt-program-dm500s-ppc
The procedure of u-Link is EXACTLY the same as USB JTAG NT.
Original video (USB JTAG NT) https://www.youtube.com/watch?v=hyz95Z_eIQQ
...
https://www.youtube.com/watch?v=_2rgLD_hV5g
Transaction
Created
4 weeks ago
Content Type
Language
video/mp4
English
Controlling
VIDEO
U-LIN
u-link-nt-as-can-bus-logger.
With MCP2515 board you can convert u-link NT into a CAN BUS logger. In the video, E39A is used with 500kbps data rate.
Connect GND,3.3V,SI,SO,SCK,CS pins . CAN HIGH and CAN LOW connect to the ECU, 120ohm resistors needed for the MCP2515 board.
...
https://www.youtube.com/watch?v=22Oxo9vYlE4
Transaction
Created
3 weeks ago
Content Type
Language
video/mp4
English
Controlling
VIDEO
U-LIN
u-link-nt-and-usb-bdm-nt-program-ecu-411
u-link NT is replacing USB BDM NT to program MC6833X CPU.
u-link NT has the highest clock set to 9MHz instead of 6MHz. The read speed is faster then USB BDM NT.
Connection
Pin 2GND (White)
Pin 3 Freeze (Gray)
Pin 4 Beer (Purple)
Pin 5 Reset (Blue)
Pin 6 DSCK (Green)
Pin 8 DSO (Orange)
Pin 10 DSI (Brown)
...
https://www.youtube.com/watch?v=vNw7D10Znmo
Transaction
Created
4 weeks ago
Content Type
Language
video/mp4
English
Controlling
VIDEO
U-LIN
u-link-nt-program-volvo-cem.
People keep on asking to get BDM NT to program the Volvo CEM since other videos has been told to do so.
u-Link NT has replaced USB BDM NT and can do the programming and better.
In this video, detailed diagram between u-Link NT and Volvo CEM is given.
150ohm resistor is used to enable the erase and programming.
...
https://www.youtube.com/watch?v=4eLyUOnv6lg
Transaction
Created
3 weeks ago
Content Type
Language
video/mp4
English
Controlling
VIDEO
U-LIN
u-link-nt-program-spc560-(compare-with
First release read speed between 140 KB/s (9Mhz clock).
No programming size limit (UDE STK has 128KB limit).
More development on SPC or MPC5XXXX coming (e200 core).
...
https://www.youtube.com/watch?v=jLo--fdKkXQ
Transaction
Created
3 weeks ago
Content Type
Language
video/mp4
English
Controlling
VIDEO
U-LIN
u-link-nt-program-24m02-and-5p08-eeprom
24M02 is a 256KB EEPROM with page size of 256 bytes. 5P08 uses SPI protocol. Both are now supported in 1.46.
If your chip is on the target boad you might not need to connect extra pins (24M02 with pull up resistors and ground pins, 5P08 W pin and hold pins might already connected properly). In the video chips are soldered to the convert board and thus some pins needs to be pulled up and some pins needs to connect to ground or power.
...
https://www.youtube.com/watch?v=4iOOiFsBulw
Transaction
Created
3 weeks ago
Content Type
Language
video/mp4
English
Controlling
VIDEO
U-LIN
u-link-nt-program-e78-boot-mode.
Recover a dead E78 with boot mode. Password is required from the shadow memory. Can bus speed is 200Khz/s. About four minutes to program the entire flash.
...
https://www.youtube.com/watch?v=1ObvHUMoBgg
Transaction
Created
3 weeks ago
Content Type
Language
video/mp4
English
Controlling
VIDEO
USBJT
usbjtag-nt-to-program-sgb6580
This video shows how to program SGB6580 (newer model).
In order to program the chip on the board you need to connect pin 7 on U2 and U3 to ground.
In here I used 27 ohm resistors.
This modem uses FL128PL, you need to remove one line in SPIflash.xml. Otherwise there will be problem to program the chip.
Remove DYB for 25L128
Save it and restart USB JTAG NT software.
Now you can read and program the modem like you do with other SPI flash modems.
...
https://www.youtube.com/watch?v=mZ2UjmFII-s
Transaction
Created
4 weeks ago
Content Type
Language
video/mp4
English
Controlling
VIDEO
STI52
sti5205-nand-flash-programming
This is implemented in 0.58. The framework for Nand flash support on ST40. The Nand raw data is backed up and programmed. (0x200 bytes sector and 0x16 bytes ecc).
0.58 should also improve the stability issue with ST40 target.
...
https://www.youtube.com/watch?v=Zve6waFAIvw
Transaction
Created
4 weeks ago
Content Type
Language
video/mp4
English