A rather lengthy video explaining my battery hack after getting jack of constant factory battery changes. Buying numerous OEM batteries was cost-prohibitive (after dropping some serious cash on the camera), so I came up with this rather simple hack.
Comment, Like, Share, and most of all Subscribe - Journey to 500 subs in 2020. Help me get there. :)
If you would like to support the channel even in the smallest way, please follow this PayPal link - https://www.paypal.com/cgi-bin/webscr?cmd=_s-xclick&hosted_button_id=R4FD8SPDTM5Q2&source=url - your support will go back in to creating more content and help secure the channel’s future. Thank you.
...
https://www.youtube.com/watch?v=oPMrYIE4bM8
A little celabratory viddy of reaching 100 subs, and a peek into some other stuff and trying a different editing style. Watch to the end. :)
If you would like to support the channel even in the smallest way, please follow this PayPal link - https://www.paypal.com/cgi-bin/webscr?cmd=_s-xclick&hosted_button_id=R4FD8SPDTM5Q2&source=url - your support will go back in to creating more content and help secure the channel’s future. Thank you.
...
https://www.youtube.com/watch?v=M_3Uu2BZZOA
Part 3 in this series, I finally test this amplifier, woohoo! Watch to find out more!
Part 1 here - https://youtu.be/JdihJ0FAjUI
Part 2 here - https://youtu.be/NHGMaFGnmH8
Support the channel (shout me a coffee ☕?);
Paypal.me/XYZConcepts
https://www.subscribestar.com/xyz-concepts
The XYZ Concepts Discord channel - https://discord.gg/T8qBgc
Follow me over on Odysee - https://odysee.com/$/invite/@xyzconcepts:c
Follow me on Twitter - @xyz_concepts
Intro music used in this video credited to:
Andreas Theme - by Kevin MacLeod (incompetech.com)
Licensed under Creative Commons: By Attribution 4.0 License
http://creativecommons.org/licenses/by/4.0/
#Repair #Electronics #To1000subs
...
https://www.youtube.com/watch?v=pbuW0Ip4fvA
*UPDATE* Please be aware that this unit (at least mine) did not have an earth grounded case - mains earth was only traced to the soldering handle and tip. A small mod is required to ensure you have an earth grounded case to prevent possible shock in a fault scenario. Check video #31 addressing this dangerous issue. Stay Safe!
I was setting up for a review of the KSGER T-12 Soldering Station when an unfortunate event ensued. Join me in this serious (haha) fault investigation.
If you would like to support the channel even in the smallest way, please follow this PayPal link - https://www.paypal.com/cgi-bin/webscr?cmd=_s-xclick&hosted_button_id=R4FD8SPDTM5Q2&source=url - your support will go back in to creating more content and help secure the channel’s future. Thank you.
...
https://www.youtube.com/watch?v=cowgbwU3b5c
I fit a "higher power" laser to my existing and lethargic Elekslaser A3 platform, so how easy is it? Are there any traps for young players? Watch and find out. ?
Depending on the response, I may do a material cutting test video putting this unit through its paces.
If you want to support the channel shout me a coffee ☕?.
https://Paypal.me/XYZConcepts
The XYZ Concepts Discord channel, come and say hi, tell me about a project you are working on - https://discord.gg/T8qBgc
Follow me over on Odysee - https://odysee.com/$/invite/@xyzconcepts:c
Follow me on Twitter - @xyz_concepts
#Elekslaser #SculpfunS9
...
https://www.youtube.com/watch?v=2x15mnNRAgo
All my other equipment has the 3-pin IEC mains socket except this has the figure 8 - 2 pin connector. Let's change that!
#electronics
...
https://www.youtube.com/watch?v=K_G7j_F8dio
Repurposing a salvaged rack mount power outlet for my standing workbench. One of a few mods as I build this bench for the shop.
If you would like to support the channel even in the smallest way, please follow this PayPal link - https://www.paypal.com/cgi-bin/webscr?cmd=_s-xclick&hosted_button_id=R4FD8SPDTM5Q2&source=url - your support will go back in to creating more content and help secure the channel’s future. Thank you.
...
https://www.youtube.com/watch?v=9eL7ViEPqlg
I take a look at some laser engraver accessories that the kind folk at Sculpfun 3D sent me - let's dive right in and take a closer look! Are these items up to the task? Let's find out!
All opinions and findings expressed in this video are my own and are not influenced in any way.
However, I was under the influence of a lot of COFFEE! ??
Timestamps - Holy cow there's a lot!
0:00 - Intro
0:22 - Delivery Day
0:48 - Unboxing Honeycomb Bed
1:55 - Unboxing Rotary Roller
4:32 - Honeycomb Bed Overview
9:04 - Rotary Roller Overview
10:07 - Thank you to Sculpfun and all my subs
10:26 - Let’s get this show on the road
10:45 - Honeycomb Bed Setup
12:00 - Airflow and Ventilation
12:32 - Solid bed test
14:26 - Honeycomb bed test
15:41 - Cut comparison
17:11 - Rotary Roller overview
19:58 - Rotary Roller setup
20:54 - No more thumb screws
21:48 - Rotary Roller setup (continued)
24:04 - First rotary roller movements
24:56 - Lightburn setup
26:10 - Spotted a minor whoopsie
26:57 - Engraving on test stock
27:28 - Test result @ 0.2mm line resolution
27:51 - Close up - Test result @ 0.2mm line resolution
28:06 - Close up (Novelty Toilet roll) - Test result @ 0.1mm line resolution
28:20 - Pros and Cons
31:47 - Sign off
33:03 - Montage outro
33:49 - Your turn!
If you want to support the channel shout me a coffee ☕?.
https://Paypal.me/XYZConcepts
The XYZ Concepts Discord channel, come and say hi, tell me about a project you are working on - https://discord.gg/T8qBgc
Follow me over on Odysee - https://odysee.com/$/invite/@xyzconcepts:c
Follow me on Twitter - @xyz_concepts
#Sculpfun3D #Laser #RotaryRoller
...
https://www.youtube.com/watch?v=zRAmGxoW7FI
Full video for this repair, here - https://youtu.be/M1rkL4ejQ7w
1. Remove the broken pin.
2. Fabricate a replacement pin from an old bolt.
3. Happy customer.
#mechanical #repair #automotive
...
https://www.youtube.com/watch?v=1wOyPnPbwls