Solid State Bedini Stromaufnahme und Ladestrom current draw and charging current
Solid State Bedini
Stromaufnahme am Eingang: 100 mA
Ladestrom am Ausgang ca. 50 - 100 mA je nach Einstellung mit ca. 200 Volt HF DC Pulsen, Äther statt Elektronen...
Am Ausgang muß eine Batterie oder Kondensator als Gegen-Kapazität sein zum starten! Über das Poti müssen beide Schwingkreise (Trigger & Power) in Resonanz gebracht werden!
Schaltplan siehe Video!
Solid State Bedini
Input current draw: 100 mA
Charging current at the ouput ca. 50 - 100 mA, depending on tuning, with ca. 200 Volt HF DC spikes, Ether - not electrons...
At the output there must be a battery or capacitor as counter-capacitance to start! Both tank circuits (trigger & power coil + respective battery / capacitor) must be brought into resonance via the potentiometer!
"Copyright Disclaimer Under Section 107 of the Copyright Act 1976, allowance is made for "fair use" for purposes such as criticism, comment, news reporting, teaching, scholarship, and research. Fair use is a use permitted by copyright statute that might otherwise be infringing. Non-profit, educational or personal use tips the balance in favor of fair use."
I OWN NOTHING in this video, posted for educational purposes only.
Song used is called: "Jalandhar"
Direct Link to the patent can be found here: http://web.archive.org/web/20061212232445/http://www.magneticpowerinc.com/mpi-patentapplication.pdf
Bedini Lüfter Motor mit solid state Magneten = Floyd Sweet´s VTA, Blochwall-Generator?
Ich hatte mich immer über den solid state Modus vom Bedini-Lüfter gewundert, wo dieser dann sogar die höchsten Spannungsspitzen abgab...
Heute beim dran rum basteln und auseinander nehmen kam mir dann die Idee, doch mal feststehende Dauermagnete an die Spulen dran zu machen...
Kaum war ein Magnet dran, funktionierte er im solid state Modus; und je mehr Magnete dran waren, umso höher wurde die Ausgangsspannung...
Magnete jeweils an 2 gegenüber liegenden Spulen, und in N - S, sich anziehender Anordnung, waren am effektivsten.
Bei ca. 12,5 V Batteriespannung am Eingang sank diese beim Einschalten dann auf ca. 10,5 V ab um ca. 2 V; während dann am Ausgang je nach dem bis zu ca. 26,0 V messbar waren.
Erinnert mich sehr an den VTA von Floyd Sweet und den Blochwall-Generator von Don Smith...
Video von Tom Bearden zu Floyd Sweet´s VTA: • Tom Bearden Floyd Sweet's Secrets
John Bedini soll ja auch angeblich damals Floyd Sweet geholfen haben...
• Video
Wobei viele Infos dazu im Netz wohl falsch sind...
Statt Luftspulen braucht es wohl Spulen mit Eisenkernen, die Magnete müssen nicht unbedingt vorher kondidioniert werden, und Kondensatoren dienen eher als Stromsammler, -verstärker am Ausgang, um entsprechende Leistung für Verbraucher zu haben...
Siehe auch das Buch "The Don Smith Magnetic Resonance Energy Crafting Systematic Index" von Richard Friedrich.
https://r-charge.3dcartstores.com/Don...
Nachtrag: Ein Kondensator muß vorher auf 20 V oder mehr aufgeladen sein, damit die Schaltung weiter läuft und nicht aus geht. Und man sollte am Poti bei steigender Spannung im Kondensator dann die Frequenz nachregeln.
Bedini fan motor with solid state magnets = Floyd Sweet's VTA, Blochwall generator?
I had always wondered about the solid state mode of the Bedini fan, where it then even emitted the highest voltage peaks ...
Today, while tinkering with it and taking it apart, I had the idea to attach permanent magnets to the coils ...
As soon as there was a magnet on it, it worked in solid state mode; and the more magnets there were, the higher the output voltage ...
Magnets each on 2 opposing coils, and in N - S, attracting arrangement, were most effective.
With approx. 12.5 V battery voltage at the input, which then sank by approx. 2 V when switched on to approx. 10.5 V; while at the output up to approx. 26,0 V.
Reminds me a lot of Floyd Sweet's VTA and Don Smith's Blochwall generator ...
Video by Tom Bearden about Floyd Sweet's VTA: • Tom Bearden Floyd Sweet's Secrets
John Bedini is said to have helped Floyd Sweet back then ...
• Video
Although a lot of information on the Internet is probably wrong ...
Instead of air-cored coils, coils with iron cores are needed, the magnets do not necessarily have to be conditioned beforehand, and capacitors rather serve as current collectors and amplifiers at the output in order to have appropriate power for loads...
See also the book "The Don Smith Magnetic Resonance Energy Crafting Systematic Index" by Richard Friedrich.
https://r-charge.3dcartstores.com/Don...
Addendum: A capacitor must first be charged to 20 V or more so that the circuit continues to run and does not turn off. And you should readjust the frequency on the potentiometer when the voltage in the capacitor increases.
Joule Thief läuft ohne Basis am Transistor
http://elektronik-labor.de/Notizen/NPNkipp.html
https://www.elektronik-labor.de/Notizen/NPNkipp3.html
https://www.elektronik-labor.de/Notizen/NPNkipp2.html
Ein Transistor ist ja quasi eine Diode mit einem 3. Anschluss...
Und eine Diode ist quasi so ungefähr das Halbleiter Equivalent zu einer Funkenstrecke...
Und Funkenstrecken waren die ersten Trigger für Schwingkreise, für Radiosender...
Joule Thief runs without base connection to transistor
http://elektronik-labor.de/Notizen/NPNkipp.html
https://www.elektronik-labor.de/Notizen/NPNkipp3.html
https://www.elektronik-labor.de/Notizen/NPNkipp2.html
A transistor is more or less a diode with a 3rd connection...
And a diode is more or less the semiconductor equivalent of a spark gap...
And spark gaps were the first triggers for oscillating circuits, for radio transmitters...
Bedini Schaltung & Floyd Sweet VTA / solid state Bloch-Wall Generator, Power In & Power Out ...
Rein: 12,22 V x 0,120 A = 1,466 W
Raus: Ca. 150 V x leider fiel das Messgerät um, aber sagen wir nur - 5 A ...
150 V x 5 A = 750 W ...
Entscheide selbst, wie viel Leistung ein 4700 µF-Kondensator aufnehmen kann ... wie viel Ampere er abgeben kann ...
Und dieses Setup hat nur eine sehr kleine Spule mit sehr kleinen Drähten (vermutlich 0,2 und 0,5 mm)... und 4700 µF sind auch für solche Kondensatoren sogar klein...
ABER EIN IST SICHER; DIESE SPANNUNG UND STROMSTÄRKE IST TÖDLICH, DIE KANN DICH TÖTEN, WIE EINE WANDSTECKDOSE !!!
SEI IMMER SEHR VORSICHTIG MIT GROSSEN KONDENSATOREN!!!
Siehe auch das Video von Tom Bearden, "Floyd Sweet´s Secrets": https://www.youtube.com/watch?v=W_Rcm...
Die beiden Magneten oben und unten sind Barium-Ferrit Magnete 100 x 100 x 20 mm groß.
Bedini Circuit & Floyd Sweet VTA / solid state Bloch-Wall Generator, Power in & Power out...
In: 12,22 V x 0,120 A = 1,466 W
Out: Ca. 150 V x sadly the meter shaked, but let´s say, only - 5 A...
150 V x 5 A = 750 W...
Decide yourself, how much power a 4700 µF capacitor can hold... how much Amperes it can let out...
And this setup has only a very small coil with very small wires on it (I guess 32 and 24 AWG)... and 4700 µF is also even small for such capacitors...
BUT ON IS SURE; THIS VOLTAGE AND AMPERAGE IS DEADLY; IT CAN KILL YOU, LIKE A WALL SOCKET!!!
BE ALWAYS VERY CAREFULL WITH BIG CAPACITORS!!!
See also Tom Bearden's video, "Floyd Sweet's Secrets": https://www.youtube.com/watch?v=W_Rcm...
The both magnets up and down are barium ferrit magnets, ca. 3,9" x 3,9" x 0,78" big.
Solid state Bedini Spulen um 90° zu Magneten gedreht
War ein Versuch, dem VTA von Floyd Sweet näher zu kommen...
Hat zwar so mit der 3. Spule nicht funktioniert, aber war schon interessant, wie sich der Resonanzpunkt dann verschoben hat, man das Poti anders einstellen mußte, und der Ton scheinbar viel lauter wurde...
Solid state Bedini coils 90° turned to magnets
This was an attempt to get closer to Floyd Sweet's VTA (Vacuum Triode Amplifier) ...
It didn't work like that with the 3rd coil, but it was interesting how the resonance point then shifted, you had to adjust the potentiometer differently, and the sound apparently got much louder ...
Mahlzeit und herzlich Willkommen bei ollisTubes,
neulich hab ich bei Bigclivelivedotcom ein Video über LED Filamentlampen gesehen, die speziell für Dubai hergestellt wurden. Diese sollen besonders effizient arbeiten und dadurch auch langlebiger sein. Bei uns sind diese Lampen nicht erhältlich ! Die Filamente der hier erhältlichen LED-Lampen werden mit höheren Strömen betrieben was für mehr Wärme sorgt und schnelleren Verschleiß.
In einem zweiten Video hat er versucht hier erhältliche LED Filamentlampen mittels Vorschaltkondensator mit weniger Netzspannung zu betreiben. Das funktioniert mit einigen Lampen - nicht mit allen. Das habe ich nun auch in meiner Werktischbeleuchtung so realisiert. Wie ich das gemacht habe seht ihr in diesem Video.
Diesmal nichts mit Röhren, aber doch mit Netzspannung betrieben. Also auch hier meine Warnung:
*Achso wer das was ich hier zeige nachmacht tut das auf eigene Verantwortung - Netzspannung reicht locker aus, um jemanden umzubringen. Wenn ihr also nicht vom Fach seid, dann lasst besser die Finger davon**
Und nun - lasst es (besser nicht) glühen.
Oliver
Bigclivelivedotcom - The lamps you are not allowed to have
https://www.youtube.com/watch?v=klaJqofCsu4&t=0s
Bigclivelivedotcom - Make your own Dooby lamps - DIY Dubai lamps (strobing alert)
https://www.youtube.com/watch?v=ISTB0ThzhOY&t=0s
Intro / Outro:
Track: The Whole Other | Go Get 'Em Tiger
• Video
BACKGROUND HARD ROCK MUSIC FOR VIDEOS - Copyright Free Music
Rock N Stock
https://www.youtube.com/watch?v=teebxO9ipcA&t=0s
Das Geheimnis von General A.B.C. Smith - Photoelektrische Augenprothesen im 19. Jahrhundert ?
The secret of General A.B.C. Smith - Photoelectric ocular prostheses in the 19th century?