It's to turn this into a FULL TIME Fan-supported Channel: We need your help with funding! https://www.paypal.me/adventureswithjim
http://advetnureswitjim.com
Check out the cool geode HERE! http://cgi.ebay.com/ws/eBayISAPI.dll?ViewItem&item=121793084415
Just had to go see if the massive storms of hurricane Joaquin turned up any new targets at a couple of my favorite sites. Well, not so much, but fun to try anyways :-)
...
https://www.youtube.com/watch?v=9cY8qwtQTc0
http://drunkfarm.com
Jim
PO BOX 402
BRONSON, FL
32621
GET YOUR DRUNK FARM T SHIRTS HERE:
https://adventures-with-jim.creator-spring.com/listing/classic-drunk-farm-2
...
https://www.youtube.com/watch?v=h_JEkRPcsjg
It's to turn this into a FULL TIME Fan-supported Channel: We need your help with funding! https://www.paypal.me/adventureswithjim
http://www.adventureswithjim.com jump in the chat!
It was a evil out there, hard rain so I couldn't film much, but still had a good day with the crew on the beach!
...
https://www.youtube.com/watch?v=DGG7yH1McFM
We have a new mailing address ! PO Box 3213 Rapid City SD 57709
Help support the channel http://www.paypal.me/happyinsanity
...
https://www.youtube.com/watch?v=MN2uPOyhdCs
It's to turn this into a FULL TIME Fan-supported Channel: We need your help with funding! https://www.paypal.me/adventureswithjim
http://adventureswithjim.com hit the chat!
The EPIC BLACK T's are still in stock, only a few left, get yours now! http://adventureswithjim.com/store2
I realized this is going to be a long video, so I'm going to break it up into a couple of parts, maybe later put together a single version.
But it's time to hack the IDX and install the Mr. Bill mods. When I was using this machine daily, I got amazing performance out of it, just didn't want to screw up whatever made this thing go. NOW I use the Tekentics G2 full time, IDX is gathering dust...so lets have some fun with it!
The full list of the Mr. Bill, as written by the man himself...
"
Seeing that I have got out of the metal detecting busness. I thought I would pass this on to you all.
Be very carefull unsoldering the componets. Distroying the circuit traces is very easy to do.
Remove VR1 Trimmer off the board. Replace with a 50k linear taper, single turn potentiometer.
Remove VR4 trimmer off the board replacing it with a 100k linear taper, single turn potentiometer.
Mount these potentiometer’s externally on the top of the case.
Replace resistor R24 with a 2.2 Meg. You could have either a 470k or a 1.5 Meg there depending on when the unit was manufactured.
Check resistor R7. If it’s not a 51 ohm resistor, replace it with one of that value. It’s most likely a 100 ohm from factory. Later manufactured units had 51 ohms.
For potentiometer wiring, I use flat multi wire such as type used in computers for component connection to the board. I cut a 2 wire, 7.5” piece for the 50k ground balance pot, and a 3 wire 7.5” one for the 100k threshold pot. I secure these wires with a wire tie to the head phone & speaker wire near the connectors. I used one other wire tie to secure the pot wires together up near the pots.
Caution. Be sure that the pot closest to the end of the case doesn’t short out against the installed board components.
S.A.T changes. R32 220k resistor can be changed out. Raising the value slows the SAT. I have been installing a 375k running it through a toggle switch with the 220k. Giving a high & low setting of the SAT. One could use a potentiometer for variable results.
If your detector uses a ID meter, open the meter case, and replace resistor R28 (3.9 meg) with a 10 meg resistor. This aids in increasing the meter response depth. "
...
https://www.youtube.com/watch?v=q9AMarcyiJA
It's to turn this into a FULL TIME Fan-supported Channel: We need your help with funding! https://www.paypal.me/adventureswithjim
http://adventureswithjim.com hit the chat!
Thanks to Nectar for the cool shirt too! http://detecting365.com
This is my first wet test of the amazing little SJCAM M10...in the Atlantic.
I know, I'm not going to win any National Geographic awards with this underwater footage...the idea was to test the waterproof case on the M10, get some real footage to see how the cam performs underwater. One of the surprises was how close things need to be to focus...and that's an important hunk of information when it comes to designing a better underwater camera rig.
Despite my shaky camera work and the murky, turbid waters of the Atlantic, the M10 continues to impress...not sure how deep this case can go, I was doing a few quick tests down to 3 feet for a few minutes at a time to check for any leaks or moisture before I destroyed the cam. The other question is of course, how much light is down there...stay tuned more fun aquatic fun for sure!
...
https://www.youtube.com/watch?v=yQ8i0zkohXg
It's to turn this into a FULL TIME Fan-supported Channel: We need your help with funding! https://www.paypal.me/adventureswithjim
http://www.adventureswithjim.com
Just screwing around with the shitty web cam, maybe time for the live show to return? I dunno, sounds like fun...
...
https://www.youtube.com/watch?v=-TKdoIc3XaQ